Abstract:Three-dimensional printing of composites reinforced by continuous fiber and based on heat-resistant materials requires a prepreg compatible with these plastics. This kind of a prepreg, in its turn, would necessarily have to be similar to these plastics in terms of its chemistry and operational thermal range. This work was an investigation of factors relevant for the strength of adhesion between carbon fiber and polymeric binder. The authors managed to develop the compounds (coupling agents) facilitating fiber impregnation with polymer and improving fiberbinder adhesion. To obtain a thermoplastic binder various polyimide matrices have been synthesized. The properties of polymers thus created were studied as per the methods of thermogravimetric analysis (TGA) and Differential Scanning Calorimetry (DSC), as well as measurement of limiting wetting angle. Then these materials were subject to solution impregnation so as to obtain prepreg samples suitable for 3D printing. Impregnation quality of these samples was studied by means of scanning electronic microscopy. The most promising prepreg samples were used for 3D printing of try-out product specimens. Composites based on the plastics reinforced by continuous fibers (glass, carbon, polymeric, etc.) are widely used in special fields of today’s technology [1–4]. They have already become indispensable for rocketry or aircraft industries, and they are steadily gaining ground in other industries, too, like machine engineering, shipbuilding, civil engineering, etc. Polymeric composite have become so popular because they are quite strong [5, 6] and light [7] at the same time. Today, manufacturing of fiber-reinforced composites is quite tedious and only allows a limited scope of geometries for final products [8] because fiber impregnation with viscous solutions/melts of polymers is a difficult process. Besides, final product takes time to harden, so until it happens it needs a moulding cast or skeleton to maintain its shape. This tedious process of product manufacturing from the parts reinforced with continuous fiber might proceed much easier and with greater automation thanks to 3D printing as per fused deposition modeling (FDM) technique that uses a filament of preimpregnated fiber [9]. In particular, one of the techniques steadily improving today is 3D printing with continuous carbon fiber and prepregs based on epoxy binders. Final products manufactured as per this technology and reinforced by continuous carbon fiber feature stable size and complex shape. However, prepregs based on epoxy resins will work only with the materials that have good adhesion with them, otherwise final composites will be too weak. Current materials can only be used for the products with low operational temperatures whereas hi-tech applications require strong and heat-resistant materials. To meet this requirement, it is necessary to develop prepregs based on heat-resistant compounds, as well as filaments based on heat-resistant plastics compatible with these prepregs. Polyimides as a class of compounds have long been known to remain stable at high temperatures. Therefore, prepregs based on them, as well as polyimide matrices fit for FDM 3D printing technique will pave way to the products simultaneously featuring high thermal resistance and good strength. The purpose of this work was to develop prepregs based on carbon fiber and polyimides featuring good resistance to high temperatures and aggressive media, as well as to develop thermoplastic polyimide matrices fit for 3D printing.

Development of new composite materials for 3D-printing based on polyimide binders and continuous carbon fiber

3D Printing for High Performance Fiber Reinforced Polymer Composites

High-content continuous carbon fiber reinforced multifunctional prepreg filaments suitable for direct 3D-printing

Investigation of a 3D Printing Method for Continuous Carbon Fiber-Reinforced Thermosetting Epoxy Composite

Preparation and 3D printing of high-thermal-conductivity continuous mesophase-pitch-based carbon fiber/epoxy composites

Processing, mechanical characterization, and micrography of 3D-printed short carbon fiber reinforced polycarbonate polymer matrix composite material

A Novel Route to Fabricate High-Performance 3D Printed Continuous Fiber-Reinforced Thermosetting Polymer Composites

High-Performance Polymer Blends: Manufacturing of Polyetherimide (PEI)–Polycarbonate (PC)-Based Filaments for 3D Printing

Additive manufacturing of high‐strength polyamide 6 composites reinforced with continuous carbon fiber prepreg

Technology and mechanical properties of reinforced continuous fiber 3D-printed thermoplastic composite

Development of a High Strength Polymeric Composite Material Using 3D-Printing and Vacuum Impregnation Technology

Enhanced Impregnation Behavior and Interfacial Bonding in CF/PEEK Prepreg Filaments for 3D Printing Application

Designing Prepregnation and Fused Filament Fabrication Parameters for Recycled PP- and PA-Based Continuous Carbon Fiber Composites

Impregnation and Interlayer Bonding Behaviours of 3D-Printed Continuous Carbon-Fiber-reinforced Poly-Ether-ether-ketone Composites

Processing of carbon fiber for 3D printed continuous composite structures

Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing

Mechanical Characterization and Production of Various Shapes Using Continuous Carbon Fiber-Reinforced Thermoset Resin-Based 3D Printing

Process-induced Property Loss of Prepreg Filaments with Continuous Fiber Content of 65 Vol% Suitable for Direct 3D Printing

3D Printing of Ultrahigh Strength Continuous Carbon Fiber Composites

Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation

Material Extrusion 3D Printing of PEEK-Based Composites