Abstract:Continuous carbon fiber-reinforced (CCFR) thermoset composites have received significant attention due to their excellent mechanical and thermal properties. The implementation of 3D printing introduces cost-effectiveness and design flexibility into their manufacturing processes. The light-assisted 3D printing process shows promise for manufacturing CCFR composites using low-viscosity thermoset resin, which would otherwise be unprintable. Because of the lack of shape-retaining capability, 3D printing of various shapes is challenging with low-viscosity thermoset resin. This study demonstrated an overshoot-associated algorithm for 3D printing various shapes using low-viscosity thermoset resin and continuous carbon fiber. Additionally, 3D-printed unidirectional composites were mechanically characterized. The printed specimen exhibited tensile strength of 390 ± 22 MPa and an interlaminar strength of 38 ± 1.7 MPa, with a fiber volume fraction of 15.7 ± 0.43%. Void analysis revealed that the printed specimen contained 5.5% overall voids. Moreover, the analysis showed the presence of numerous irregular cylindrical-shaped intra-tow voids, which governed the tensile properties. However, the inter-tow voids were small and spherical-shaped, governing the interlaminar shear strength. Therefore, the printed specimens showed exceptional interlaminar shear strength, and the tensile strength had the potential to increase further by improving the impregnation of polymer resin within the fiber.

What problem does this paper attempt to address?

The paper mainly addresses the following issues: ### Research Background and Objectives - **Continuous Carbon Fiber Reinforced (CCFR) Thermoset Composites** have garnered widespread attention due to their excellent mechanical and thermal properties. - **3D Printing Technology** introduces cost-effectiveness and design flexibility, especially advantageous in manufacturing complex geometries. - **Light-Assisted 3D Printing Technology** can utilize low-viscosity thermoset resins to manufacture CCFR composites, which are traditionally difficult to print. ### Challenges Faced - When using low-viscosity thermoset resins for 3D printing, it is challenging to manufacture various shapes due to the resin's lack of shape retention capability. - Previous studies have improved the composite's volume fraction, reduced void content, and enhanced mechanical properties by adjusting resin flow rate and printing speed. ### Research Objectives - Design an "overshoot" algorithm based on the light-assisted 3D printing process to enable printing various shapes using low-viscosity thermoset resins. - Mechanically characterize unidirectional printed specimens to determine their tensile strength and interlaminar shear strength. - Conduct void analysis to understand the size, shape, and distribution of voids within the specimens and define their impact on tensile and interlaminar properties. ### Main Findings - Developed an overshoot-associated printing path algorithm, making it possible to manufacture various shapes using low-viscosity thermoset resins through light-assisted 3D printing technology. - The printed unidirectional composite specimens exhibited good mechanical properties, including a tensile strength of 390 ±22 MPa and an interlaminar shear strength of 38 ±1.7 MPa. - Void analysis showed that the printed specimens contained 5.5% overall voids, with irregular cylindrical intra-fiber voids affecting tensile performance, while smaller, spherical inter-fiber voids impacted interlaminar shear strength. In summary, this study successfully manufactured continuous carbon fiber reinforced composites with excellent mechanical properties using low-viscosity thermoset resins by developing a new printing path algorithm and optimizing printing parameters.

Mechanical Characterization and Production of Various Shapes Using Continuous Carbon Fiber-Reinforced Thermoset Resin-Based 3D Printing

A Mechanical Performance Study of Dual Cured Thermoset Resin Systems 3D-Printed with Continuous Carbon Fiber Reinforcement

Adjustment of Mechanical Properties of 3D Printed Continuous Carbon Fiber-Reinforced Thermoset Composites by Print Parameter Adjustments

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

A Novel Route to Fabricate High-Performance 3D Printed Continuous Fiber-Reinforced Thermosetting Polymer Composites

Carbon Fiber-Thermoplastic Composite 3D Printing Technology and Its Self-Monitoring

Mechanical and Material Characterization of 3d Printed Continuous Fiber Reinforced Photopolymer Matrix Composites

Investigation of a 3D Printing Method for Continuous Carbon Fiber-Reinforced Thermosetting Epoxy Composite

3D Printing of Ultrahigh Strength Continuous Carbon Fiber Composites

Direct-write 3D printing of UV-curable composites with continuous carbon fiber

Self-monitoring Continuous Carbon Fiber Reinforced Thermoplastic Based on Dual-Material Three-Dimensional Printing Integration Process

3D printing for continuous fiber reinforced thermoplastic composites: mechanism and performance

Preparation and characterization of 3D printed continuous carbon fiber reinforced thermosetting composites

Process evaluation, tensile properties, mathematical models, and fracture behavior of 3D printed continuous fiber reinforced thermoplastic composites

Three-dimensional printing of continuous carbon fiber-reinforced shape memory polymer composites

An investigation into mechanical properties of a 3D printed two-matrix continuous fiber composites with multi-cavity structure

Process-dependent Multiscale Modeling for 3D Printing of Continuous Fiber-reinforced Composites

Investigation on the mold‐less curing process of 3D printing continuous carbon fiber reinforced thermoset composites based on thermoplastic shells constraint

Embedded 3D printing of UV-curable thermosetting composites with continuous fiber

Effect of process parameters on properties of 3D printed continuous fiber reinforced thermoplastic composites

Parameter design of continuous carbon fiber-reinforced phenolic resin composites via in situ-curing 3D printing technology