Abstract:Publication date: 2 October 2023 Source: Key Engineering Materials Vol. 957 Author(s): Carlos Rodríguez-Mondéjar, Alvaro Rodríguez-Prieto, Ana Maria Camacho The development of composite materials has meant, over the last few decades, a challenge for research in relation to the search for new ways of manufacturing. Currently, a wide variety of materials and processes have a high degree of development and industrial applications, but the potential for improvement in this area promotes the search for new systems that allow obtaining products with better mechanical characteristics and better manufacturability. Within this framework of the development of processes and applications, the following combination of manufacturing technologies is proposed: thermoforming and overmolding of carbon fiber reinforced thermoplastics with continuous and short fibers respectively. The aim of this work is to provide a hybrid technology to manufacture sandwich panels whose stiffening core geometry can be highly optimized based on the load requirements considered in the design of the product of interest. The proposed process consists of the prior shaping by thermoforming process of a continuous fiber-reinforced thermoplastic laminate on one of the surfaces of the manufacturing mold that will later be used for injection of the core structure with a counter-mold adapted for this purpose. The injection of the short fiber reinforced thermoplastic will be carried out in such a way that one of the surfaces of the resulting cavity is directly in contact with the previously formed laminate, giving rise to an overmolding. After this operation, a closing laminate will be formed that will give the panel the desired resistance. A detailed analysis of the different stages of this process is necessary, especially with regard to the processing parameters (e.g. injection temperature, pressure, polymer velocity, and interface temperature), orientation of the fiber resulting from the injection process, the adhesion of the polymer between stages, and the geometric limitations of considered sub-processes. The analysis is performed using a finite element method (FEM) software and analytical approaches.

Forming of Panel with Ribs of Thermoplastic Carbon-Fiber Composites Using Die Cushion

A Novel Method for Through-Thickness Reinforcement of Laminated Composites Using Discrete Micro-Polarization-induced Fiber Injection (DMFI) Approach

Preparation and Validation of a Longitudinally and Transversely Stiffened Panel Based on Hybrid RTM Composite Materials

Analysis of the Possibility of Forming Stiffening Ribs in Litecor Metal-Plastic Composite Using the Single Point Incremental Forming Method

Rubber mandrel design suitable for manufacture co-cured hat-stiffened composite panel with large curvature by auto fiber placement technique

Experimental and numerical studies on two-point incremental forming of woven fabric composite sheet

Repurposed Discontinuous Fiber Composites for industrial applications: Effects of average number of platelets through the thickness, platelet length, and hybridization on flexure properties

The use of discontinuous PEEK/carbon fiber thermoplastic moulding compounds for thick-section componentry

Novel Approach toward the Forming Process of CFRP Reinforcement with a Hot Stamped Part by Prepreg Compression Molding

Experimental investigation of thermoset composite laminates manufactured with a novel sheet-winding compression-molding (SWCM) process

Preparation of High-Performance Carbon Fiber-Reinforced Epoxy Composites by Compression Resin Transfer Molding

Evaluation of the mechanical properties and deformability of metal-based composite sheets made of thin stainless-steel sheets and carbon fiber reinforced plastics

CF Reinforced Thermoplastic Hybrid Process Proposal for the Optimization of Sandwich Panels Stiffness and Processability

Development of Thermoplastic Composite Reinforced Ultra-High-Performance Concrete Panels for Impact Resistance

Structure Design on Thermoplastic Composites Considering Forming Effects

The Research on RTM Molding Process of Thin-wall Rib Structure of Composite Materials

Additive manufacturing of sandwich panels with continuous fiber reinforced high modulus composite facings

A Modeling Framework for the Thermoforming of Carbon Fiber Reinforced Thermoplastic Composites

Manufacture of braided-textile reinforced multi-walled tubular structures and axial compression behaviors

Manufacturing and Testing of a CFRC Sandwich Cylinder with Kagome Cores

Conventional and Microcellular Injection Molding of a Highly Filled Polycarbonate Composite with Glass Fibers and Carbon Black