Abstract:The heat transfer and flow of nanofluids in microchannel heat sink is usually numerically investigated by the single-phase model. The thermal conductivity and viscosity of nanofluids are calculated in the whole computational region because the single-phase model, assumes the nanofluids is static and nanoparticles concentration is uniform. However for the actual forced flow process, the concentration distribution of the nanofluids is not uniform. So the thermal properties of the nanofluids vary within different computational regions. With the increase of the velocity of the nanofluids, the deviation between the prediction of single-phase model and experimental results increases. In this paper, a new simulation method is proposed to consider the inhomogeneous and dynamic thermophysical properties of the nanofluids by obtaining the nonuniformly distributed nanoparticle concentration in each numerical cell. At the same time, it takes into account the following factors: the interactions between the nanoparticles, the solid wall and the base fluid, the axial conduction, the slip boundary conditions and fluid-solid coupling. The results show that the proposed numerical simulation method further improve the simulation accuracy for the forced flow and heat transfer process of nanofluids in the microchannel in a wider range. The effects of the nanoparticles concentration, Reynolds number and axial heat transfer on the thermophysical properties of the nanofluilds, the flow and heat transfer characteristics of a rectangular microchannels with hydraulic dimensions of 341μm were analyzed using the proposed simulation model. The main results are as follows: the nanoparticles are enriched at the near wall for the fully developed region; the nonuniformity of the nanofluilds thermal conductivity coefficient distribution at the channel cross section increases with the increase of the mass flow rate and the inlet centration; under the same Reynolds number, the higher the nanofluids concentration the better the heat transfer characteristics, but there is no linear relationship between the enhancement amplitude and concentration; the heat transfer coefficient of nanofluid with 1% and 2% alumina nanoparticles concentration is about 5.86% and 8.49% higher than that of deionized water, respectively; the axial conduction effect cannot be ignored for the microchannel, which significantly affects the inlet and outlet region of the microchannel especially when the Reynolds number is low. The nanofluilds temperature in the microchannel increases with the curve and does not match the conventional linear growth hypothesis.

Flow and heat transfer characteristics of a nanofluid as the coolant in a typical MTR core

Property of Water-Nanoparticle Flow and Heat Transfer in the Double-Tube Heat Exchanger with Nanofluid

Enhancing Thermal–Hydraulic Performance in Nuclear Reactor Subchannels with Al2O3 Nanofluids: A CFD Analysis

Convective Heat Transfer and Resistance Characteristics of Nanofluids with Cylindrical Particles

Numerical Study of Flow and Heat Transfer Characteristics for Al2O3 Nanofluid in a Double-Pipe Helical Coil Heat Exchanger

Numerical Research on Convective Heat Transfer and Resistance Characteristics of Turbulent Duct Flow Containing Nanorod-Based Nanofluids

Numerical Investigation of Laminar Convective Heat Transfer and Pressure Drop of Water-Based Al 2 O 3 Nanofluids in a Microchannel

Flow Characteristics of Heat and Mass for Nanofluid under Different Operating Temperatures over Wedge and Plate

Heat transfer and flow features of Al2O3-water nanofluids flowing through a circular microchannel - Experimental results and correlations

Numerical investigation of the magneto-hydraulic-thermal performance of a nanofluid in a semi-porous wavy channel

Experimental study on cooling performance of nanofluid flow in a horizontal circular tube

Numerical Analysis of MHD Nanofluid Flow Characteristics with Heat and Mass Transfer over a Vertical Cone Subjected to Thermal Radiations and Chemical Reaction

Numerical simulation on thermohydraulic performance of different types of nanofluids in a corrugated-triangular channel

Numerical investigation of heat transfer and fluid flow characteristics of ternary nanofluids through convergent and divergent channels

Simulation on Influences of Al2O3 Nanofluids As Coolant for Nuclear Power Plant Based on Modified Empirical Formula of Nanofluids Thermal Properties at High Temperature and High Pressure

Heat and mass transfer analysis of conducting non-Newtonian nanofluid flows over an elongating sheet with a non-uniform heat source

Single-phase fluid flow and heat transfer characteristics of nanofluid in a circular microchannel: Development of flow and heat transfer correlations

Cooling characteristics and entropy production of nanofluid flowing through tube

Numerical study of the effects of geometric parameters and nanofluid properties on heat transfer and pressure drop in helical tubes

Numerical analysis of unsteady free convection of Al 2 O 3 inside a tubular reactor under the influences of exothermic reaction, and inclined MHD as an application to chemical reactor

Numerical investigation on forced convection in rectangular cross section micro-channels with nanofluids