Abstract:Ethylene is one of the largest building blocks in the petrochemical industry, mainly produced by steam cracking of ethane derived from naphtha or shale gas at high temperatures (>800 °C). Despite its technical maturity and economic competitiveness, the thermal steam cracking of ethane is highly energy-intensive. Herein, an electrochemically engineered direct conversion process of ethane to produce hydrogen and ethylene using a planar protonic ceramic membrane reactor with a bi-functional three-dimensional catalytic electrode is reported, with a single-pass ethane conversion of 40% and ethylene yield of 26.7% at 550 °C. Compared with the industrial ethane steam cracking, this method saves process energy input by 45.1% and improves process energy efficiency by 50.6%, based on comprehensive process simulation using Aspen Plus software. Further, steam electrolysis treatment under the solid oxide electrolysis cell mode can regenerate the system's catalytic performance and significantly alleviate catalytic degradation by 74%, demonstrating high techno-economic viability.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acscatal.1c03351.Fabrication procedures of electrochemical cell with 3D anode; XRD patterns and EDS mapping of PBFM material under different atmospheres; schematic of the in-house built dual-zone reactor; detailed process flow diagram of an EEDC process for Aspen Plus simulation; selectivity of various hydrocarbon products in the EEDC process at different temperatures above 600 °C under OCV conditions; C2H6 conversion and C2H4 yield at different applied currents, operating temperatures, and C2H6 feedstock concentration; electrochemical performance under EEDC and SOEC modes; results of Faraday efficiency measurement; GC raw data showing the formation of higher (C3+) hydrocarbon products in the EEDC process; TGA results and calculated coke content under different applied currents and after regeneration; C2H4 yield during each operation cycle with intermittent regeneration; cell resistance and SEM images of the integrated anode before and after the test; STEM image of PtGa/ZSM-5 catalyst before and after EEDC process; XPS result of the PtGa/ZSM-5 catalyst before and after reaction; assumptions for the Aspen Plus simulation of the EEDC process; reactions and corresponding conversions inside the EEDC reactor at 40 mA·cm–2 assumed for Aspen Plus simulation; process result summary of ethylene production from steam-ethane cracking and EEDC at an applied current density of 40 mA cm–2; specific energy input and output for the EEDC process; surface chemical composition of the PtGa/ZSM-5 catalyst before and after reaction (PDF)This article has not yet been cited by other publications.

New Technology for Production of Dicyclopentadiene and Methyl-Dicyklopentadiene

Mechanistic Understanding of Efficient Polyethylene Hydrocracking over Two-Dimensional Platinum-Anchored Tungsten Trioxide.

Gas Production from Polyethylene Terephthalate Using Rotating Arc Plasma

Product Distribution of Thermal Cracking of exo-Tetrahydrodicyclopentadiene

Advanced Catalyst Technology for Broad/Bimodal Polyethylene, Achieved by Polymer-Coated Particles Supporting Hybrid Catalyst

Improved Interfacial Adhesion And Manufaturing Method Of Mgf/P-Dcpd Composites Using W, Mo, Or Ru Type Catalysts In Air Condition

Pyrolysis of Polyolefins Using Rotating Arc Plasma Technology for Production of Acetylene

Downer Catalytic Pyrolysis (DCP): A Novel Process for Light Olefins Production

Kinetics on Thermal Dissociation and Oligomerization of Dicyclopentadiene in a High Temperature & Pressure Microreactor

Optimal design and plantwide control of novel processes for di-n-pentyl ether production

Enhancement of the Acetylene and Ethylene Yields from Ethane by Partially Decoupling the Oxidation and Pyrolysis Reactions

Experimental Study of Partially Decoupled Oxidation of Ethane for Producing Ethylene and Acetylene

Reaction Injection Molding of Dicyclopentadiene

Development and Intensification of the Ethylene Process Utilizing a Catalytic Membrane Reactor

Fundamental studies and pilot verification of an olefins/aromatics-rich chemical production from crude oil dehydrogenation catalytic pyrolysis process

System integration and evaluation of residual oil deep catalytic cracking process coupled with CO 2 recycle to produce polypropyl carbonate

Heavy Oil to Chemicals: Multi-Stage Downer Catalytic Pyrolysis

Electrochemically Engineered, Highly Energy-Efficient Conversion of Ethane to Ethylene and Hydrogen below 550 °C in a Protonic Ceramic Electrochemical Cell

Production of Ethylene from Ethane Fraction by a Method Alternative to Steam Cracking

Dynamic simulation of high-pressure tubular reactor for low-density polyethylene production

Hydrotreating of middle distillates with addition of pyrolysis oil from depolymerisation of waste plastics