Abstract:There are growing concerns about the stresses created by shielding currents in high field superconducting magnets fabricated from tape conductors leading to reduced performance and lifetime. This paper presents results of stress/strain calculations caused by shielding currents assuming the conductor deformations follow a linear constitutive relation. An anisotropic bulk approximation approach was used to calculate the electromagnetic field distributions in a REBCO high field coil with a stack of pancakes and a large number of turns first, and then the Lorentz force distribution and mechanical response characteristics were studied in the two-dimensional axisymmetric configuration. A new discrete contact mechanical model implemented by the finite element method, which is able to simulate the contact and separation behaviors between adjacent turns during the deformation, was proposed to analyze the distributions of hoop stress, hoop strain, radial stress and radial displacement in the coil. The influences of shielding current on those mechanical responses were obtained by comparing the simulation cases with and without taking shielding current into account. Besides, a continuum bulk mechanical model, which is parallel to the discrete contact mechanical model and treats the pancakes as continuum bulks, was modeled as well in order to understand the influences of different models on the simulation results. Furthermore, we studied the influences of a couple of practical factors (including the n-value, ramp rate, and operating mode of the REBCO coil winding) on the shielding current and hoop stress. A couple of novel and important conclusions were found. (1) Neglecting the shielding current behavior would significantly underestimate the maximum local hoop stress in a REBCO high field coil. (2) The continuum bulk mechanical model is not adequate for the stress analysis of dry-wound high field coils, by which unreasonably large tensile radial stresses could be obtained. (3) The highest local hoop stresses at the fully-charged moment and the fully-discharged moment are located in a certain pancake near the end of the coil winding and the end pancake, respectively. (4) Decreasing the n-value and the ramp rate of the REBCO coil could be two auxiliary ways to suppress the shielding current and maximum local hoop stress in the coil. (5) For the ramp-and-hold operating mode, the REBCO coil experiences the highest stress level at the moment when it right achieves the goal field. (6) The cycling operation of a REBCO high field coil can cause the tape experiencing alternative positive and negative hoop stresses and this may decrease the fatigue life of the tape and then the life of a magnet.

Strain Distribution and Critical Current Characteristics of an Individual REBCO Tape and Quasi-Isotropic Superconducting Strand Under Bending Loads by the Layerwise Theory

Effect of Bending Strain on the Current-Carrying Performance of Copper-Laminated REBCO Tape

Current Transfer Length in Quasi-isotropic Strand Made from REBCO Tapes Under Transverse Pressures

Numerical analysis on electromagnetic and mechanical properties of the quasi-isotropic strand

Critical Current Degradation Behaviour of Various REBCO Tapes under Uniaxial Strain

Bending Characteristics of Stacked REBCO Cable under Different Stacking Modes

Experimental Study on Cabling Properties of Different REBCO Coated Tapes

Structural Analysis of REBCO Coated Conductors and Quasi-Isotropic Strands under Bending Using Continuum Shell Element

Experimental Study on Critical Current of Bent ReBCO Tapes in CORC Type Cable

Experiments and FE Modeling of Stress–strain State in ReBCO Tape under Tensile, Torsional and Transverse Load

Experimental Study on the Critical Current of CORC Cable under Cyclic Bending-straightening

Analysis of Damage Behavior of REBCO Stacked Tapes under Bending Loads

Mechanical Behavior and Critical Current Density Variation of the Twisted Stacked-Tape Slotted-Core Cable-in-conduit Conductor under Bending and Axial Tensile Load

Numerical Simulation of the Mechanical Behavior of Superconducting Tape in Conductor on Round Core Cable Using the Cohesive Zone Model

Stress, Strain and Electromechanical Analyses of (re)ba2cu3oxconductors Using Three-Dimensional/two-dimensional Mixed-Dimensional Modeling: Fabrication, Cooling and Tensile Behavior

Electro-Mechanical Behavior In Arrays Of Superconducting Tapes

Strain Effect on Critical Current Degradation in Bi-Based Superconducting Tapes with Different Deformation Modes

Stress and Strain Analysis of a REBCO High Field Coil Based on the Distribution of Shielding Current

Numerical Analysis of the Mechanical and Electrical Properties of CORC Cables under Torsional Loading

Bending-Peeling Method to Research the Effect of Lateral Stress on Superconductivity of REBCO Tape at Liquid-Nitrogen Temperature

Bending Characteristics of a Transposed Cable (xcable) with In-Plane Bending of REBCO Tapes