Abstract:Heat treatments are inevitable not only in the production of rare earth barium copper oxide (REBCO) tapes, but also in their post-processing for applications, typically, in soldering and epoxy/wax impregnation during the fabrication of REBCO coils. In general, the heat treatment of REBCO tapes should be carried out at lower temperature for a shorter time, but the specific safe boundary of heat-treatment temperature and time for REBCO tapes is still unknown. Therefore, a comprehensive study on the typical electrical, mechanical, and electromechanical characteristics of REBCO tapes after heat treatments under temperature of 250 °C is necessary. This work focus on the copper-encapsulated REBCO tapes, which are more robust (while with much lower engineering current density) to be processed in application systems than the tapes without encapsulation. The critical current degradation, stress-strain characteristic, and electromechanical properties of REBCO tapes were measured after heat treatments at different temperatures in argon and oxygen atmosphere. A 2D finite element analysis model was established for detailed stress/train analyzes under tension and bending based on the analysis of residual stress/strain. The results indicate that the critical current of the copper-encapsulated REBCO tapes decreases with increasing heat-treatment temperature and dwell time, and is of no evident relation to atmosphere. In addition, increased temperature of heat treatment leads to an obvious decrease in the yield strength and critical tensile stress. This effect is mainly attributed to the degradation of mechanical properties of the encapsulated copper layer, which is demonstrated by the combination of our finite element simulation and the experiments results. Interestingly, the change in the critical bending radius due to heat treatments was slight, because the bending axial strain of the REBCO layer remained almost unchanged after heating. It is also worthy to note that all the properties tested in this study were irrelevant to the external oxygen partial pressure during the heating process. As a practical conclusion for the application systems, an upper and atmosphere-irrelevant limit of processing temperature of 130 or 150 °C (2 h dwell time) was proposed for copper-encapsulated REBCO tapes, under which the critical current, yield strength, critical tensile stress/strain and critical bending radius of the copper-encapsulated REBCO tapes decay by < 1% or 3%, respectively.

Bending-Peeling Method to Research the Effect of Lateral Stress on Superconductivity of REBCO Tape at Liquid-Nitrogen Temperature

Critical current degradation and delamination crack observation of epoxy-coated REBCO superconducting tapes after thermal cycles in liquid nitrogen

Synergic realization of electrical insulation and mechanical strength in liquid nitrogen for high-temperature superconducting tapes with ultra-thin acrylic resin coating

Bending–Peeling Method to Measure Interface Strength of YBCO Tape

<i>In situ</i> detection of delamination and critical current degradation caused by the thermal stress in epoxy impregnated REBa<sub>2</sub>Cu<sub>3</sub>O<sub>7</sub>- coils

Performance study of REBCO multi-filament tapes/ CORC cables prepared by reel-to-reel mechanical incision

REBCO delamination characterization by 90 degree peel test

Numerical Study on Mechanical Behavior and Electromechanical Properties of Solder-Jointed REBCO-Coated Conductors

Delamination Avoidance in Epoxy Wet-Wound REBCO Coils by Release Agent Coating

Electromechanical degradation of REBCO coated conductor tapes under combined tension and torsion loading

Current-carrying properties of REBCO multi-filamentary tapes prepared by reel-to-reel ultraviolet picosecond laser cutting

Experimental study on the an-isotropic critical current of REBCO tape

Magnetic Field and Temperature Scaling of the Critical Current of REBCO Tapes

Deformation Behavior of Stacked REBCO Tapes under Compressive Loads

Plastic Deformation Simulation of REBCO Tapes Using Particle Methods

The geometry, purity, and grain orientation database of the Cu stabilizer layer and the effect on the electrical and thermal properties of commercial REBCO tapes

Typical electrical, mechanical, electromechanical characteristics of copper-encapsulated REBCO tapes after processing in temperature under 250 °C

High-field thermal transport properties of REBCO coated conductors

Thermal conductivity of REBCO tapes with different stabilizers from 4.2 to 200 K

Evaluation of the effect of edge cracks on critical current degradation in REBCO tapes under tensile stress

Screening-current-induced mechanical strains in REBCO insert coils