Abstract:Objective Broadband tunable mid-infrared (MIR) light sources have attracted much attention in practical applications such as spectral sensors, medical treatment, and environmental monitoring. At present, MIR emission from luminescent glass is primarily achieved through rare-earth ion doping. Its adjustable range, however, is relatively limited. As PbSe quantum dots (QDs) have a narrow band gap and a large Bohr radius, they are easily capable of achieving quantum confinement effect. PbSe QDs formed in germanate glass with low phonon energy can produce broadband tunable MIR emission spanning the wavelength range of 1. 8-2. 8 mu m. Using the melting-in-tube fiber drawing method, we successfully prepared all-solid-state PbSe QD-doped glass fiber and obtained broadband tunable emission covering 1.8-2.8 mu m. Therefore, PbSe QD-doped glass fiber is expected to be used for broadband tunable MIR light sources. Methods PbSe QD-doped germanate glass was prepared using the melting-quenching method and was selected as the core glass of glass fiber. The core glass and cladding glass were prepared into an optical fiber preform by cold working, which included rounding, perforating, polishing, and cleaning. Following that, the optical fiber preform was suspended in a resistance furnace and drawn into an optical fiber using the melting-in-tube method. The softening temperature of the cladding glass was 840 degrees C, according to the DSC curve. The PbSe QD-doped glass fiber was successfully drawn at 1000 degrees C after several attempts at various temperatures. At a heating rate of 6 degrees C min(-1), the resistance furnace was heated to 1000 degrees C. The cladding glass tube was then softened and the core glass was molten at this point. The precursor fiber was then quickly drawn without crystallization. Finally, the precursor fiber was heat treated to induce controllable precipitation of PbSe QDs in the glass fiber. Results and Discussions PbSe QD-doped glass was prepared by the melting-quenching method. The XRD spectra in Fig. 2 proved that PbSe QDs were precipitated in the heat-treated glass. Under 808 nm laser excitation, PbSe QD-doped glass could achieve broad MIR emission covering 1.8-2.8 mu m [Fig. 3( b)]. The melt-in-tube melting was used to successfully fabricate PbSe QD-doped glass fiber without crystallization. We observed from the EPMA test in Fig. 4 that the optical fiber had a good core-cladding structure with no obvious elemental migration between the fiber core and cladding. TEM was used to examine the distribution and size of QDs in a heat-treated fiber at 440 t. PbSe QD-glass fibers under different heat treatment schedules exhibited intense tunable MIR emission covering 1. 8-2.8 ttm when excited using an 808 nm laser (Fig. 7). Different heat treatments can be used to adjust the position of the emission peak. Finally, the PbSe QD-doped glass fiber had an optical loss of 17.19 dBm/m (Fig. 8). Conclusions This study presented the preparation and characterization of an all-solid-state PbSe QD-doped glass fiber with tunable broadband MIR emission. Based on the selection and optimization of the basic glass system, a size-controllable PbSe QD-doped glass was prepared and achieved broadband tunable emission in the MIR regions of 1.82.8 ttm. The core glass was a PbSe QD-doped borosilicate glass, and the cladding glass was a PbSe QD-doped borosilicate glass. The PbSe QD-doped glass fiber was successfully prepared using the melt-in-tube melting, and it was then characterized using EPMA. There was no evidence of elemental migration in the glass fibers, which had a complete core-cladding structure. When excited by an 808 nm laser, PbSe QD-doped glass fibers produced broadband tunable emission within 1.8-2.8 mu m, which was expected to be used as a broadband tunable MIR light source. Key words fiber optics; PbSe quantum dos; glass fiber; mid-infrared broadband emission; melt-in-tube melting

Preparation of especially pure Ge-Se glasses via germanium monoselenide for Mid-IR fiber optics

An optical fiber glass containing PbSe quantum dots

Sol–gel preparation of Ge nanocrystals embedded in SiO2 glasses

Fabrication of mid-IR As-Se chalcogenide glass and fiber with low scattering loss

Preparation of high-purity germanium telluride based glasses with low oxygen impurity content

Preparation of high purity glasses in the Ga–Ge–As–Se system

Se-H-free As2Se3 fiber and its spectral applications in the mid-infrared

Low-loss Ge-As-Se-Te Fiber for High-Intensity CO2 Laser Delivery

Nonlinear Ge-As-Se chalcogenide fibers

Chalcogenide Glass Microfibers for Mid-Infrared Optics

Preparation of high purity glasses based on germanium and gallium tellurides using chemical transport

Mid-infrared single-Mode As-S-Se glass fiber and its supercontinuum generation

Investigation of PbSe Quantum Dot-Doped Glass Fibers with Broadband Mid-Infrared Emission

New approach for preparation of high-purity sulfide-germanium glasses doped with praseodymium

Preparation and investigation of high purity Ge–Te–AgI glasses for optical application

Amorphous silica containers for germanium ultrapurification by zone refining

Investigation of phase separation as a source of optical losses in IR glasses for fiber optics

Development of As-Se tapered suspended-core fibers for ultra-broadband mid-IR

Crystalline Selenium Core Optical Fibers with Low Optical Loss