Split-anion solvent extraction of light rare earths from concentrated chloride aqueous solutions to nitrate organic ionic liquids

Mercedes Regadío,Tom Vander Hoogerstraete,Dipanjan Banerjee,Koen Binnemans

DOI: https://doi.org/10.1039/c8ra06055j

IF: 4.036

2018-01-01

RSC Advances

Abstract:Rare earths are extracted efficiently by nitrate ionic liquids from a chloride feed solution.

chemistry, multidisciplinary

What problem does this paper attempt to address?

Effect of polar molecular organic solvents on non-aqueous solvent extraction of rare-earth elements

Brecht Dewulf,Vincent Cool,Zheng Li,Koen Binnemans

DOI: https://doi.org/10.1016/j.seppur.2022.121197

IF: 8.6

2022-08-01

Separation and Purification Technology

Abstract:The extraction and separation of five different rare-earth elements, La, Nd, Eu, Dy and Yb, from an aqueous chloride solution and from different chloride non-aqueous solutions using the solvating extractant Cyanex 923 was investigated. As previous studies had demonstrated the potential of non-aqueous solvent extraction (NASX) to refine rare earths from ethylene glycol, structural analogues of ethylene glycol (1,2-propanediol and 1,3-propanediol) and to other polar organic solvents (triethylene glycol, dimethylsulfoxide, methanol, N,N-dimethylformamide and N,N-dimethylacetamide) were studied. The extraction data were interpreted in terms of different solvent properties: dielectric constant, Gutmann donor number, molecular structure and hydrogen-bonding capabilities. Remarkable differences were observed between the extraction behaviour from ethylene glycol, 1,2-propanediol and 1,3-propanediol. Therefore, these solvent systems were further studied to elucidate the speciation of the rare-earth elements by optical absorption and luminescence spectroscopy. Based on these studies, both contact-ion-pair formation and solvation strength are assumed to play an important role in the extraction of rare earths by Cyanex 923 from different polar organic solvents. The differences in extraction behaviour can be exploited to fine-tune the separation of rare earths.

engineering, chemical
Advances in partitioning of minor actinides and rare earths from high level liquid waster

Xue Wenjing,Jiang Jialei,Zhang Anyun,Chai Zhifang

DOI: https://doi.org/10.3969/j.issn.2095-2783.2013.03.001

2013-01-01

Abstract:Liquid-liquid solvent extraction is one of the most commonly used means in experiment and engineering for reprocessing of spent nuclear fuel and effective separation of high level radioactive waste.Research advances of effective separation of minor actinides and rare earths from high level liquid waste(HLLW) in recent 20 years have been reviewed.Based on the soft-and hard-ligands,several solvent extraction processes such as TRUEX,DIAMEX,TRPO,DIDPA,SANEX,TALSPEAK and so on have been evaluated.Some new technologies and new methods such as liquid membrane extraction,ion exchange,and extraction chromatography etc.have been discussed.Since extraction chromatography has the advantages of both solvent extraction and ion exchange,a variety of novel extraction chromatographic adsorption/separation materials have become the interesting research targets for effective separation of minor actinides and the others from HLLW.
Solvent Extraction and Separation of Heavy Rare Earths from Chloride Media Using Nonsymmetric (2,3-Dimethylbutyl)(2,4,4′-trimethylpentyl)phosphinic Acid

Junlian Wang,Meiying Xie,Huajun Wang,Shengming Xu

DOI: https://doi.org/10.1016/j.hydromet.2016.10.020

IF: 4.217

2017-01-01

Hydrometallurgy

Abstract:Nonsymmetric (2,3-dimethylbutyl)(2,4,4′-trimethylpentyl)phosphinic acid (INET-3) may be a superior extractant for extraction and separation of heavy rare earths (REs), as its extraction ability falls between that of P507 and Cyanex 272. Its purity and pKa were determined using potentiometric titration methods. The extraction mechanism and extraction equilibrium constants of INET-3 for heavy REs from chloride media were studied. The effects of the anion types (Cl−, NO3− and SO42−) and concentrations (0.1, 0.5 and 1.0mol/L) on RE(III) extraction were investigated. The extraction capacity and separation factors of INET-3 for heavy REs were determined. The stripping behaviours of heavy RE complexes with INET-3 by HCl, HNO3 and H2SO4 were examined. The results showed that the pKa of INET-3 was 5.45. The extraction capacity of INET-3 was approximately twice that of Cyanex 272 and only one-third that of P507. Loaded heavy RE(III) extracted by INET-3 was completely stripped out by HCl, HNO3 and H2SO4 solutions when the pH was at or below 1.2. Among the three inorganic acids, H2SO4 was the most effective stripping agent. INET-3 can separate heavy RE(III) efficiently, and the separation factors of adjacent heavy RE(III) βEr/Ho, βTm/Er, βYb/Tm and βLu/Yb were 3.25, 2.73, 2.96 and 1.53, respectively, when extracted from a Ho/Er/Tm/Yb/Lu quinary system.
Extraction for Rare Earth of Alkyl Imide

LIU Zhi-rong,ZHOU Li-min,LI Chuan-mao,JIANG Xiao-chang

DOI: https://doi.org/10.3969/j.issn.1007-7545.2006.05.011

2006-01-01

Abstract:New kind of imide extractant was used for separating rare earth.The experiments on extraction for rare earth show that it can enrich rare earth better and selectively.
Extraction and separation of rare earth elements using LN resins in hydrochloric acid

Samantha A. Labb,John D. Despotopulos,Kelly N. Kmak,Derek R. Hoffman

DOI: https://doi.org/10.1007/s10967-024-09785-z

2024-09-28

Journal of Radioanalytical and Nuclear Chemistry

Abstract:The separation of the rare earth elements is essential for numerous scientific applications but remains a significant challenge due to the nearly identical chemical properties of the adjacent lanthanide elements. Eichrom's LN series of extraction chromatographic resins feature organophosphorus extractants and are widely used to achieve adjacent lanthanide separations. While extensive characterization of these resins has been completed for nitric acid matrices, the use of hydrochloric acid is preferred for a variety of applications. The extraction of the rare earth elements, La–Lu and Y, has been characterized on LN and LN2 resins in hydrochloric acid via batch uptake and column chromatographic studies.

chemistry, inorganic & nuclear, analytical,nuclear science & technology
Solvent extraction and separation of light rare earths from chloride media using HDEHP-P350 system

Wenjie Zhang,Dongxia Feng,Xian Xie,Xiong Tong,Yunpeng Du,Yang Cao

DOI: https://doi.org/10.1016/j.jre.2021.05.003

IF: 4.632

2022-02-01

Journal of Rare Earths

Abstract:Solvent extraction is the most important method for rare earth extraction and separation. Currently, HDEHP and HEH/EHP are widely used in industrial production, but there are still obvious deficiencies that require further research to resolve. In this paper, the unsaponification extraction of light rare earth ions in a hydrochloric acid medium by HDEHP-P350 system was studied. The results show that the addition of P350 reduces the extraction capacity of HDEHP, and it also greatly reduces the concentration of acidity required for the back-extraction. It still has a good separation factor for light rare earths without saponification, and the extractant is not easy to emulsify. With an aqueous phase of pH=2.85, and HDEHP mole fraction of XHDEHP=0.9 (compared with O/A=2), the separation effect of light rare earth is the best, resulting in the separation coefficient βCe/La=3.39, βPr/Ce=1.67 and βNd/Pr= 1.45, respectively. The loaded light rare earth ions extracted by HDEHP-P350 can be easily stripped when 2 mol/L HCl is used as the stripping agent. Finally, the extraction mechanism is discussed using a slope method, and the final structure of the extracted complex is determined to be RECl[(DEHP)2]2P350(o), based on a combination of infrared spectrum, 1H NMR and 31P NMR analyses.<math>ReCl3(a)+2(H2A2)(o)+B(o)↔K12ReCl[HA2]2⋅B(o)+2H(a)++2Cl(a)−</math>Adding P350 reduces the extraction capacity of HDEHP and still has a good separation effect for light rare earths without saponification; the structure of the extracted complex is determined to be RECl(DEHP)2P350(o).<ol class="links-for-figure"><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S100207212100123X-ga1_lrg.jpg">Download : Download high-res image (111KB)</a></li><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S100207212100123X-ga1.jpg">Download : Download full-size image</a></li></ol>

chemistry, applied
Separation and Purification of Light Rare Earth Elements from Chloride Media Using P204 and Cyanex272 in Sulfonated Kerosene under Non-Saponification Conditions

Peiqiang Fan,Wenjie Zhang,Xiong Tong,Xian Xie,Ruiqi Xie,Qiang Song,Yunpeng Du,Yang Cao

DOI: https://doi.org/10.37190/ppmp/172444

2023-01-01

Physicochemical Problems of Mineral Processing

Abstract:The extraction of light rare earths (Pr and Nd) from chloride medium was investigated using a mixture of di(2-ethylhexyl) phosphoric acid (P204) and bis(2,4,4-trimethylpentyl) phosphinic acid (Cyanex272) in sulfonated kerosene. The P204+Cyanex272 system exerted a synergistic effect on the separation of light rare earths, and the separation coefficient was higher than when P204 and Cyanex272 were used as extractants alone. The separation coefficient of Pr and Nd in the extraction system reached 1.75 when the pH of the aqueous phase material solution was approximately 2.5, and 1.5 mol/L hydrochloric acid as a stripping agent effectively eluted the rare earth ions in the loaded organic phase. Combining the slope method, infrared spectroscopy, and nuclear magnetic resonance spectroscopy, we explored the mechanism of the extracted Nd and Pr into the organic phase complex, and finally entered the organic phase with Re(HA2)2B. The P-O-H bond and P=O bond in the extractant P204 and Cyanex272 formed a coordination bond with Re3+. Therefore, this extraction method also provides a reference for a more environmentally friendly and efficient procedure for separation and purification of light rare earth elements Pr and Nd.
Selective Recovery of Low-Concentration Light Rare Earth Ions from High-Concentration Ammonium Sulfate System by Coordination Ability

Jianghua Wu,Duchao Zhang,Tianzu Yang,Dasha Xia

DOI: https://doi.org/10.1007/s40831-023-00779-x

2024-01-22

Journal of Sustainable Metallurgy

Abstract:The selective extraction of low-concentration light rare earth ions(LREs) by 1,7-diaza-15-crown-5 ether(2N15C5) from complex ammonium sulfate solutions containing multiple impurity ions was studied, which provides a new method for efficient separation of Ln3+ from the tail liquid wastewater discharged from in-suit leaching of ion-adsorbed rare earth ores. Liquid–liquid extraction experiments showed that impurity ions affect the extraction distribution of LREs via inducing the formation of rare earth ammonium sulfate compound salts, and the single-stage extraction coefficients of LREs were 2.20 for aluminum (Al) and 7.80 for iron (Fe) under the condition of pH 1.5 ± 0.5 and [SO42−]T/∑[Ln3+] < 10. Multistage counter-current extraction can further enhance the selective extraction of light rare earth ions with βLREs/Al = 21.41 and βLREs/Fe = 23.33 from the tail liquid wastewater. Density functional theory calculations indicated that steric hindrance caused by size compatibility and electron density-based weak interactions affect the coordination between 2N15C5 and different cations.Graphical Abstract

metallurgy & metallurgical engineering,green & sustainable science & technology
Boosting the extraction of rare earth elements from chloride medium by novel carboxylic acid based ionic liquids

Yu Deng,Yigang Ding,Zhong Huang,Ying Yu,Jun He,Yi Zhang

DOI: https://doi.org/10.1016/j.molliq.2021.115549

IF: 6

2021-05-01

Journal of Molecular Liquids

Abstract:Two novel carboxylic acid based ionic liquids (ILs), benzyltributylammonium myristic acetate ([N444Bn][MA]) and benzyltributylammonium dodecanedioic acetate ([N444Bn]2[DDA]), have been rationally designed and successfully synthesized for the extraction of yttrium (denoted as Y(III)) from a chloride aqueous solution and for the separation of mixed rare earth elements (REEs). Comparison studies of the extraction performances of [N444Bn][MA] and [N444Bn]2[DDA] were carefully investigated under different conditions (e.g., equilibrium time, solution acidity, salting-out agent concentration, and REEs concentration). The results indicated that the extraction efficiency of Y(III) reached 87.18% after 2 min using [N444Bn]2[DDA], whereas it required 10 min to reach an extraction efficiency of 47.37% using [N444Bn][MA], mainly due to the larger electronegativity of the incorporated dicarboxylates in the anions of [N444Bn]2[DDA], which enhanced its coordination with Y(III) compared to [N444Bn][MA]. However, [N444Bn][MA] illustrated better selective separation behavior than [N444Bn]2[DDA] in mixed REEs solutions (including La, Nd, Eu, Ho, Yb and Y), and the selective factors of Yb and La were 16.21 and 3.30, respectively. Furthermore, the ion association mechanism, evolved from the slope analysis and FT-IR results, contributed to avoiding the saponification procedures and resultant saponification wastewater during the extraction process. In addition, the back-extraction experiments indicated that ~97% Y(III) can be stripped from [N444Bn]2[DDA] and [N444Bn][MA] using 1.0 M and 0.4 M HCl, respectively, demonstrating that these ILs can be further used in large-scale applications for the separation and recovery of REEs.

chemistry, physical,physics, atomic, molecular & chemical
New Sustainable Solvent Extraction Pathways for Rare Earth Metals via Oximes Molecules

Maria Atanassova,Rositsa Kukeva,Vanya Kurteva

DOI: https://doi.org/10.3390/molecules28227467

IF: 4.6

2023-11-08

Molecules

Abstract:A study on the synergistic extraction of Eu(III) ions with a series of chelating ligands and determination of the process parameters is presented by employing ionic liquids and typical organic diluents. The investigations of the liquid–liquid extraction, commonly applied in the separation science of 4f and 5f-ions acidic chelating compounds, 4-benzoyl-3-methyl-1-phenyl-2-pyrazolin-5-one (HP), 4-benzoyl-3-phenyl-5-isoxazolone (HPBI), and 2-thenoyltrifluoroacetone (HTTA) alone and in combination with two synergistic agents, meso-hexamethylpropyleneamine oxime (S2: HM-PAO) and its bis-imine precursor (S1: pre-HM-PAO), are presented. The interaction between the two extractants (acidic/neutral) in deuterochloroform was studied using 1H, 13C, and 1H-1H NOESY experiments. Several conclusions are given highlighting the role of the ionic diluent in complexation processes and selectivity with an employment of the two synergistic agents for various metal s-, p-, d-, and f-cations in the Periodic table, with almost 25 metal ions. The objective was to optimize a system for 4f-ions solvent extraction based on the new oxime molecules with β-diketone/isoxazolone/pyrazolone partnership. As detailed above, slight enhancements of extraction efficiencies were obtained either by using basic synergistic agents such as HM-PAO and/or using pre-HM-PAO. A competitive solvent extraction test of nearly 18 f-ions by various ligands (HTTA, S1, S2, and HPBI) and the two mixtures HTTA−S1 and HTTA−S2 diluted in ILs or organic diluents was also conducted in order to evaluate the switchable diluent impact. Additionally, electron paramagnetic resonance (EPR) spectroscopy was used to study the established chemical species with Cu2+ cations in the obtained organic extracts involving the two synergistic molecules.

chemistry, multidisciplinary,biochemistry & molecular biology
Solvent Extraction of Rare Earth Ions from Nitrate Media with New Extractant Di-(2,3-dimethylbutyl)-phosphinic Acid

Wang Junlian,Chen Guang,Xu Shengming,Yin Zhili,Zhang Qin

DOI: https://doi.org/10.1016/s1002-0721(16)60088-1

IF: 4.632

2016-01-01

Journal of Rare Earths

Abstract:As a relatively new extractant, di-(2,3-dimethylbutyl)-phosphinic acid(HYY-2) is more efficient to separate heavy rare earths Tm/Yb/Lu than Cyanex 272 and P507. In this paper, HYY-2 was synthesized in our lab, and the extraction equilibrium, thermodynamics and stripping acidity for La, Gd and Y, which stood for light rare earth elements(REE), middle REE and heavy REE respectively, from nitrate media with this extractant were investigated. Meanwhile, extraction ability, capacity and stripping acidity of HYY-2 were investigated and compared with those of Cyanex 272 and P507. The separation performance for rare earth element couples Gd/Eu and Er/Y were also studied. Compared to Cyanex 272, it possessed higher extraction capacity; while compared with P507, it has lower stripping acidity. The maximum β Gd/Eu 1.46 occurred at pH equilibrium =2.78 and the maximum β Er/Y was 1.47 when pH equilibrium = 2.01.
The enrichment and separation of lanthanides ions from wastewater using solvent sublation coupled with high speed countercurrent chromatography

Wenjuan Wang,Wenting Li,Jiaqi Shi,Saeed Ahmed Memon,Yun Wei

DOI: https://doi.org/10.1016/j.molliq.2024.124375

IF: 6

2024-03-06

Journal of Molecular Liquids

Abstract:Rare earth elements are non-renewable resources. During their processing, a lot of wastewater are produced, which poses a danger to human beings and the environment. Herein, the enrichment method of solvent sublation for La (III), Ce (III), Gd (III) and Er (III) was designed and established. Enrichment parameters pH, flotation time, extractant concentration and air flow rate were optimized. The result showed that the highest recovery of La (III) reached up to 92.33 % under the optimized conditions of pH 8, 10 min of flotation time, 0.15 mol L -1 of the extractant 2-ethylhexyl phosphate acid-2-ethylhexyl ester and 30 mL min −1 of air flow rate. The light rare earth element Ce (III) and heavy rare earth elements Gd (III) and Er (III) were also examined and obtained with maximum recovery. The stability of the extractant complexation with rare earth ions and the mechanism of competitive extraction were studied by density functional theory calculations. The extraction ability was following sequence of La (III) < Ce (III) < Gd (III) < Er (III). The enrichment of rare earth elements from real water samples was investigated and obtained result was consistent with the experiment result of synthetic solutions. The established high speed countercurrent chromatography method was used to successfully separate La (III), Ce (III), Gd (III) and Er (III) from the solution of rare earth ions enriched by solvent sublation.

chemistry, physical,physics, atomic, molecular & chemical
Rational design of novel carboxylic acid functionalized phosphonium based ionic liquids as high-performance extractants for rare earths

Yi Zhang,Weidong Guo,Donghao Liu,Jie Xu

DOI: https://doi.org/10.1016/j.jre.2020.10.005

IF: 4.632

2021-11-01

Journal of Rare Earths

Abstract:Novel non-fluorinated ILs with hydrophobic nature was designed and successfully prepared.Endowing cation with carboxylic acid group facilitates the extraction capability of REEs.Different extraction mechanisms were determined with chloride and nitrate medium.Selective separation of Sc from lanthanides are realized with undiluted extraction system.Different affinity between La/Ni, Sm/Co benefits recycling of REEs in future applications.Developing the novel ionic liquids as the potential substitutes for conventional organic solvents in extraction of the rare-earth metals is highly desirable but remains facing challenges. In this study, the well-designed carboxylic acid functionalized phosphonium based ionic liquids, (4-carboxyl)butyl-trioctyl-phosphonium chloride/nitrate, are synthesized and characterized. The as-prepared samples are tested as the undiluted hydrophobic acidic extractant for rare-earth metal ions, affording the maximal loading of 3 mol/mol towards Nd(III) in aqueous solution and the remarkable stripping performance. The results also reveal their excellent extractability and selectivity for Sc(III) in the mixtures of six rare-earth ions, as well as the outstanding separation properties between rare-earth and first row transition-metal ions (i.e., La/Ni, Sm/Co). Moreover, the extraction mechanism indicates that the extracted rare-earth complex via a proton exchange in the ionic liquid phase is structurally similar to the complexes obtained with neutral extractants. This work presents a prototype for the fabrication of the hydrophobic cation-functionalized ionic liquids for highly efficient rare-earth extraction and provides the future application in recycling of rare-earth metals from the spent magnets.Novel carboxylic acid functionalized ILs were fabricated for highly efficient undiluted extractants for REEs. Different Extraction mechanisms were illustrated respectively in chloride or nitrate media, occurring via the typical proton exchange mechanism. The different affinity enables the recycling of REEs containing applications such as SmCo magnets and NiMH batteries, as well as the separation of Sc from the lanthanides.<ol class="links-for-figure"><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S1002072120304245-fx1_lrg.jpg">Download : Download high-res image (193KB)</a></li><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S1002072120304245-fx1.jpg">Download : Download full-size image</a></li></ol>

chemistry, applied
Hydrochloric Acid Recovery from Rare Earth Chloride Solutions by Vacuum Membrane Distillation (1) Study on the Possibility

JJ Tang,KG Zhou,FG Zhao,RX Li,QX Zhang

IF: 4.632

2003-01-01

Journal of Rare Earths

Abstract:The equilibrium between the gas-liquid phases of the system of HCl-RECl(3)-H(2)O was analyzed, and the possibility of hydrochloric acid recovery from rare earth chloride solutions by vacuum membrane distillation (VMD) was experimentally studied in the laboratory scale. The results indicate that increasing initial concentrations of both hydrochloric acid and rare earth increase recovery ratio of hydrochloric acid, and recovery ratio of 80% can be achieved. Concentrated multiple of rare earth shows great influence on recovery ratio, leakage ratio of rare earth is less than 2% generally, and pure acid can be acquired in the permeate side. The two factors, namely flux and leakage ratio, which may determine the future use of VMD were also discussed.
Fast Extraction and Enrichment of Rare Earth Elements from Waste Water Via Microfluidic-Based Hollow Droplet

Zhuo Chen,Wen-Ting Wang,Fu-Ning Sang,Jian-Hong Xu,Guang-Sheng Luo,Yun-Dong Wang

DOI: https://doi.org/10.1016/j.seppur.2016.10.059

IF: 8.6

2017-01-01

Separation and Purification Technology

Abstract:The conventional solvent extraction set-up for low-concentration rare earth elements (REEs) at high phase ratios has shortcomings including large factories, long mixing times, high energy consumption, extractant loss and easy emulsification. In this work, a solvent extraction system for Nd(III) using 2-ethylhexyl phosphoric acid-2-ethylhexyl ester (P507) was investigated to enhance extraction in a microfluidic device to solve the above problems. The effects of residence time and phase ratio on the extraction efficiency of a liquid-liquid system were studied. The results showed that extraction efficiency increased as the residence time increased significantly, and a longer channel was required to reach equilibrium for higher phase ratios than for others owing to the decreased oil flow rate and increased mass transfer distance. We also investigated the effects of outlet length, phase ratio, and gas flow rate on the extraction efficiency of a gas-liquid-liquid system. The results indicated that only 0.3 m of the outlet channel was required to reach equilibrium for the entire process, and the overall volume mass transfer coefficient k(L)a was 5-50 times larger than in systems without a gas phase. The enrichment factor could reach 200-450 with an initial concentration of 30-90 ppm, and the extraction efficiency was higher than 90% even at a high phase ratio of 200. A theoretical model was built to predict the intensification of extraction by the gas-filled hollow droplet. Finally, europium and erbium were chosen as the typical medium and heavy rare earth systems to prove the applicability of this method. (C) 2016 Elsevier B.V. All rights reserved.
Efficient Extraction and Stripping of Nd(III), Eu(III) and Er(III) by Membrane Dispersion Micro-Extractors

Zhuo Chen,Jianhong Xu,Funing Sang,Yundong Wang

DOI: https://doi.org/10.1016/j.jre.2018.02.001

IF: 4.632

2018-01-01

Journal of Rare Earths

Abstract:The extraction of low concentration rare earth elements at high phase ratio was investigated. The traditional extraction set-up, such as mixer-settler, have drawbacks of easy emulsification, difficult separation and low efficiency if operated at the above condition. Membrane dispersion micro-extractor, owing to its well-dispersed, high surface-to-volume ratio and fast mass transfer rate, was employed in our work. Nd(III), Eu(III), Er(III) were chosen to represent light, medium, heavy rare earth elements (REEs). The extraction process of REEs with 2-ethylhexyl phosphoric acid-2-ethylhexyl ester (P507) was investigated by membrane dispersion micro-extractors. Firstly, the extraction equilibrium of these three elements was explored in the stirred conical flasks, and it is indicated that the extraction efficiencies can be 0.95, 0.97 and 0.98, respectively within 40 min at phase ratio of 100:1. Then the effects of operational conditions such as the residence time, organic and aqueous flow rates on extraction efficiency were also explored in micro-extractors. The results indicate that the efficiency decreases and then increases if increasing aqueous phase flow rate, residence time and droplets' diameter are the key factors of this process. Increasing the phase ratio reduces the extraction efficiency significantly. When the REEs solution has an initial pH of 4.00, the flow rates of continuous and dispersed phase are 40 and 1.6 mL/min, respectively, and 90 mg/L Nd (III), Eu(III) and Er(III) is extracted by 1 mol/L P507 at the out-let length of 8 m. The extraction efficiencies are 0.978, 0.983 and 0.991, respectively. Finally the stripping process was also studied with the micro-extractor. The stripping efficiencies of Nd(III), Eu(III) and Er(III) can reach 0.99, 0.96 and 0.91, respectively when the out-let length is 8 m and the concentration of hydrochloric acid is 1 mol/L. The developed approach offers a novel and simple strategy on the fast extraction and enrichment of low concentration rare earth elements from waste water. (C) 2018 Published by Elsevier B.V. on behalf of Chinese Society of Rare Earths.
Separation of rare earth elements by synergistic solvent extraction with phosphonium-based ionic liquids using a β-diketone extractant and a neutral ligand

Yusuke Tsuchida,Daiki Nomizu,M. Matsumiya,Y. Sasaki

DOI: https://doi.org/10.1080/07366299.2021.1889761

2021-03-01

Solvent Extraction and Ion Exchange

Abstract:ABSTRACT We investigated the solvent extraction of four rare earth (RE) elements (Pr, Nd, Tb, and Dy) from Nd-Fe-B magnets using mixtures of 1-(2-thienyl)-4,4,4,-trifluoro-1,3-butanedione (Htta) or 4,4,4-trifluoro-1-phenyl-1,3-butanedione (Hbfa) chelating extractants and tri-n-octylphosphine oxide (TOPO) neutral ligand in phosphonium-based ionic liquids. Based on the results of slope analysis data, the following equations were proposed for the RE extraction: A synergistic effect was observed for the extraction of the RE elements with the combination of extractant and neutral ligand. The values of the equilibrium constant and separation factor were also evaluated in this study. The results reveal that the [NTf2]− anion did not participate in the extraction mechanism of the RE elements, and the Raman spectroscopic analysis of the extracted phase also supported the proposed stoichiometry of the extracted complex. Furthermore, the separation of Tb(III) and Dy(III) from other RE(III) components was investigated through a series of hydrometallurgical processes, which consisted of leaching, removal of [Fe(OH) x ]3-x , and solvent extraction. Finally, the separation of Tb(III) and Dy(III) from other RE(III) components was performed with seven extraction cycles using the HL + TOPO/[P2225][NTf2] system.

Materials Science,Chemistry
Selective extraction of rare earths and lithium from rare earth fluoride molten-salt electrolytic slag by nitration

Huazhou Hu,Jinliang Wang

DOI: https://doi.org/10.1016/j.hydromet.2021.105552

IF: 4.217

2021-03-01

Hydrometallurgy

Abstract:The extraction of rare earth elements (REEs) from rare earth fluoride molten-salt electrolytic slag has recently attracted attention because of the potential environmental hazards of this material and its rich content of valuable REEs. In this study, we used a selective nitration method to completely transform powdered samples into a nitrate mixture. We conducted a suitable selective roast-water leaching treatment, which resulted in >98% extraction efficiency for the REEs and Li; oxides of Fe and Al were left behind in the residue, which was attributed to the lower decomposition temperature of Fe(NO3)3 and Al(NO3)3. Furthermore, F volatilized in the exhaust as HF and was absorbed by an alkaline solution. HSC modeling and TG-DTA were conducted to simulate the nitration process to obtain the optimum conditions for electrolytic slag nitration. Fe, Al, and F impurities were separated from the lixivium to a great extent, thereby enabling the production of REE oxalates with >99% purity. Such a solution could be directly processed to extract metals without the need for pretreatments to remove impurities. The defluorination method and subsequent extraction of REEs and Li from fluoride molten-salt electrolytic slag address the exponential increase in REE production.

metallurgy & metallurgical engineering
Monoalkyl Esters of Isoalkylphosphonic Acid As Extractants in Rare Earth Separation

陈德朴,钟攸兰,梁树权

1992-01-01

Abstract:nitric acid as eluent,thulium,ytterbium andlutetium can be separated quantitatively.The extractant-loaded resins possess high column efficiency with goodkinetic characteristics.The extraction mechanism was also explored.
Lipophilic EDTA-based ligands in different diluents for the extraction of rare earths: Preliminary results with Nd(III), Dy(III) and Pr(III) in chloride and nitrate media

Tamir Sukhbaatar,Raphaëlle Piton,Fabrice Giusti,Guilhem Arrachart,Magali Duvail,Aarti Kumari,Santosh Daware,Shally Gupta,Sriram Goverapet,Sushanta Kumar Sahu,Beena Rai,Stéphane Pellet-Rostaing

DOI: https://doi.org/10.1016/j.hydromet.2024.106415

IF: 4.217

2024-10-24

Hydrometallurgy

Abstract:A separation method for the recovery of neodymium(III) from two different media, chloride and nitrate, by implementing solvent extraction technique with a novel lipophilic diamide derivative of ethylenediamine tetraacetic acid (EDTA), namely 2,2'- N , N ′-didecyl-dioxo- N , N′ , N′′ , N′′' -tetraazatetratriacontane- N′′ , N′′' -diyl diacetic acid ( H 2 E4C 10 ), has been investigated. Initial screening results demonstrated acceptable solubility (ca. 15 mM) of the diamide in 1,3-diisopropylbenzene (DiPB) and in a 93:7 v:v n -dodecane: n -octanol mixture (DOm) as non-polar diluents. Further investigations aiming at determining operational parameters associated with the befitted extractant systems were conducted at pH ranging from 2 to 4 in chloride and nitrate media. A pH-dependent performance of the proposed systems revealed loading capacity peaking at pH = 3 with the respective values of 1.7 and 2.0 g L −1 in nitrate and chloride media. The extraction efficiency, the distribution coefficients, and the separation factor ( E %, D and SF , respectively) were determined for an equimolar mixture of neodymium and two other potential competitive lanthanides, namely dysprosium and praseodymium. The best selectivity was observed in the chloride medium at pH = 4 yielding SF Nd/Pr = 1.48 and SF Nd/Dy = 2.03. Neodymium-to-extractant stoichiometry was evidenced in chloroform to be 1:1 H 2 E:Nd at pH = 2. Thermodynamic constants related to the considered extraction equilibrium have been determined by using the Van't Hoff relation and the slope analysis method. It appeared within the selected pH-range that the mechanism of the Nd 3+ transfer was strongly influenced by the nature of the diluent. This was illustrated by the enthalpy-driven transfer when Nd 3+ was extracted with the H 2 E-4C 10 -Dom system (aliphatic diluent) while the transfer became entropy-driven when the extraction was performed with the H 2 E-4C 10 -DiPB system (aromatic diluent). The complexation of Nd 3+ involved mainly the participation of both the amide and carboxylic functional groups. The transfer of the cation to the organic phase might occur through the formation of the Nd( HE ) A 2 complex (where A is either a nitrate or a chloride anion), allowing for the lowest associated standard Gibbs free energy of transfer (−28 < ΔG ° < −24 kJ mol −1 ) regardless of the aqueous feed.

metallurgy & metallurgical engineering

Split-anion solvent extraction of light rare earths from concentrated chloride aqueous solutions to nitrate organic ionic liquids

Effect of polar molecular organic solvents on non-aqueous solvent extraction of rare-earth elements

Advances in partitioning of minor actinides and rare earths from high level liquid waster

Solvent Extraction and Separation of Heavy Rare Earths from Chloride Media Using Nonsymmetric (2,3-Dimethylbutyl)(2,4,4′-trimethylpentyl)phosphinic Acid

Extraction for Rare Earth of Alkyl Imide

Extraction and separation of rare earth elements using LN resins in hydrochloric acid

Solvent extraction and separation of light rare earths from chloride media using HDEHP-P350 system

Separation and Purification of Light Rare Earth Elements from Chloride Media Using P204 and Cyanex272 in Sulfonated Kerosene under Non-Saponification Conditions

Selective Recovery of Low-Concentration Light Rare Earth Ions from High-Concentration Ammonium Sulfate System by Coordination Ability

Boosting the extraction of rare earth elements from chloride medium by novel carboxylic acid based ionic liquids

New Sustainable Solvent Extraction Pathways for Rare Earth Metals via Oximes Molecules

Solvent Extraction of Rare Earth Ions from Nitrate Media with New Extractant Di-(2,3-dimethylbutyl)-phosphinic Acid

The enrichment and separation of lanthanides ions from wastewater using solvent sublation coupled with high speed countercurrent chromatography

Rational design of novel carboxylic acid functionalized phosphonium based ionic liquids as high-performance extractants for rare earths

Hydrochloric Acid Recovery from Rare Earth Chloride Solutions by Vacuum Membrane Distillation (1) Study on the Possibility

Fast Extraction and Enrichment of Rare Earth Elements from Waste Water Via Microfluidic-Based Hollow Droplet

Efficient Extraction and Stripping of Nd(III), Eu(III) and Er(III) by Membrane Dispersion Micro-Extractors

Separation of rare earth elements by synergistic solvent extraction with phosphonium-based ionic liquids using a β-diketone extractant and a neutral ligand

Selective extraction of rare earths and lithium from rare earth fluoride molten-salt electrolytic slag by nitration

Monoalkyl Esters of Isoalkylphosphonic Acid As Extractants in Rare Earth Separation

Lipophilic EDTA-based ligands in different diluents for the extraction of rare earths: Preliminary results with Nd(III), Dy(III) and Pr(III) in chloride and nitrate media