Abstract:Cordierite honeycomb ceramics are sintered under a range of sintering atmosphere and temperature conditions. The linear thermal expansion coefficient (CTE) is measured along the extrusion direction. The samples sintered in an enclosed crucible have a much lower CTE than those sintered in open air. The CTE decreases with increasing sintering temperature up to 1450 °C. The polymorphic phases, texture, amorphous phase, impurity crystals, and porosity are analyzed using scanning electron microscopy, HR‐TEM, porosimeter, and Rietveld refinement method. The sintered samples consist of two polymorphic phases: indialite (hexagonal symmetry) and cordierite (orthorhombic symmetry). Both the volume % of the cordierite phase and the crystal texture increase with increasing sintering temperature. The orthorhombic distortion of cordierite from the hexagonal lattice (indialite) increases with increasing sintering temperature. The characteristic six‐membered ring of the (Si,Al)‐O4 tetrahedra in the cordierite structure shows substantial changes in the bond length due to Al‐Si ordering. Amorphous phase and impurity crystal phases such as silimanite and spinel remain at temperatures as high as 1450 °C. The effect of the polymorphic phases, the degree of texture, amorphous phase, impurity crystal phases, and the orthorhombic distortion is discussed in relation to the CTE characteristics of honeycomb. The sintered honeycomb consists of two polymorphic phases, indialite (hexagonal symmetry) and cordierite (orthorhombic symmetry). The volume % of cordierite phase and the crystal texture increase with increasing sintering temperature. The thermal expansion coefficient (CTE) reduces with the sintering temperature. The orthorhombic distortion originates from Al‐Si ordering. Amorphous and silimanite phases are ascribed to higher CTEs of the samples sintered in open air.

Crystalline Phase Analysis and Thermal Expansion Coefficient Calculation of Quartz-Sand/Corundum Composites

Design and preparation of BaO–Al2O3–SiO2–B2O3/Quartz LTCC composites with tailored coefficient of thermal expansion

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Tuning high and low thermal expansion coefficients of Li2O–BaO–Al2O3–B2O3–SiO2/quartz LTCC composites by replacing quartz partly with α-Al2O3 or ZrO2

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Thermal decomposition and reaction sintering for synthesis of mullite-zirconia composite using kaolin, γ-alumina and zirconia

Thermal Expansion of 3C-SiC Obtained from In-Situ X-ray Diffraction at High Temperature and First-Principal Calculations

Crystal Structure and Thermal Expansion Coefficient of Cordierite Honeycomb Ceramics

Phase transformation of Y-Ce-TZP/Al2O3 composite ceramic annealed in air

Thermal Mechanical Property Enhancement with Silicon Carbide Ceramic Filled Composites for Industrial Applications

Fabrication and Characterization of Ceramic Coatings with Alumina–silica Sol-Incorporated Α-Alumina Powder Coated on Woven Quartz Fiber Fabrics

The influence of zirconium dioxide nanoadditives on the properties of mullite-corundum

The Thermal Expansion Behaviour of SiCp/Al–20Si Composites Solidified under High Pressures

Study of phase transformation of calcium silicate using desert sand as raw materials

Structural-Phase State and Properties of SiC Ceramics Obtained by Ultrasound-Assisted Liquid-Phase Sintering with Eutectic Additives

Sand corrosion, thermal expansion, and ablation of medium‐ and high‐entropy compositionally complex fluorite oxides

High-temperature thermal expansion behaviour of C/SiC studied using an in-situ optical visualisation method and numerical simulations in a quartz lamp array heating environment

Thermal Stability, Mechanical Properties and Ceramization Mechanism of Epoxy Resin/Kaolin/Quartz Fiber Ceramifiable Composites

Preparation and Characterization of Alumina-coated Hollow Quartz Fiber Reinforced Al2O3-SiO2 Aerogel Composite

Microstructure, Dislocation Density and Thermal Expansion Behavior Using Thermo Elastic Models of Zircon Sand Reinforced as Cast ZA-27 Composites

Correlation between phase content and mechanical properties of SiCw- ZTA composites sintered by SPS