Abstract:With the advancement of laser powder bed fusion (LPBF) for aluminum alloys, developing novel lightweight Al–Li alloy systems present enormous potential for aerospace applications. Conventional Al–Mg–Li alloys exhibit low densities but suffer from poor strength due to the lack of inherent strengthening phases. In the present work, a novel lightweight Al–Mg–Li–Ag-Sc-Zr alloy was developed for LPBF after optimizing the processing parameters. The as-built alloy featured a bimodal microstructure consisting of fine equiaxed grains and columnar grains. The submicron primary Al 3 (Sc, Zr) phases with a cubic L 1 2 structure served as inoculants for grain refinement and exhibited good coherency with the α-Al matrix. Besides, submicron spherical quasicrystalline T-Mg 32 (Al, Ag) 49 phases of and nanometer rod-shaped S 1 –Al 2 MgLi phases were scattered inside the grains. These results produced a yield strength (σ y ) of 286 ± 8 MPa, ultimate tensile strength (σ UTS ) of 406 ± 3 MPa, and elongation at fracture (ε f ) of 12.5 ± 0.3%. The direct aging at 325 °C for 12 h led to an increase in hardness to a peak value of 170 HV. The secondary phases at the grain boundaries were breached and a large amount of submicron T and S 1 phases within the grains were prominently increased. Besides, spherical Al 3 (Sc, Zr, Li) and tiny δ′-Al 3 Li precipitates were observed in the α-Al matrix. A considerably enhanced σ y of 375 ± 12 MPa and σ UTS of 469 ± 4 MPa were achieved mainly due to the particle strengthening but decreased ε f to 5.8 ± 0.2%. The alloys in both states exhibited a moderate work-hardening capability. The feasibility of LPBF for lightweight Al–Li alloy was successfully established but required further optimization of the alloy composition.

A Low-Cost Lightweight Entropic Alloy with High Strength

Lightweight Al-based entropy alloys: Overview and future trend

Microstructure, Mechanical and Wear Properties of Low-Density Cast Medium and High Entropy Aluminium Alloys

Development of lightweight Al-based entropy alloys for elevated temperature applications

Deformation-driven Modification Towards Strength-Ductility Enhancement in Al–Li–Mg–Zn–Cu Lightweight High-Entropy Alloys

First principles-based design of lightweight high entropy alloys

Preparation and Electrochemical Properties of AlMgZnSnPbCuMnNi High Entropy Alloys with Low Free Corrosion Potentials

Tailoring Compressive Strength and Absorption Energy of Lightweight Multi-Phase AlCuSiFeX (X = Cr, Mn, Zn, Sn) High-Entropy Alloys Processed via Powder Metallurgy

Microstructure and mechanical properties of the (TiZrV)100-xAlx medium-entropy alloys

Engineering ultra-strong Mg-Li-Al-based light-weight alloys from first principles

A novel Ti45V45(AlCrMo)10 lightweight medium-entropy alloy with outstanding mechanical properties

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance

An as-cast Ti-V-Cr-Al light-weight medium entropy alloy with outstanding tensile properties

Effect of composition on the microstructure and mechanical properties of Mg-Al-Zn alloys

Precipitation strengthening in an ultralight magnesium alloy

Low-cost and high-strength Mg-Al-Ca-Zn-Mn wrought alloy with balanced ductility

Influence of Al-Si eutectic alloy on the mechanical behaviors and microstructure feature of ultralight dual-phase Mg-8Li-x(Al-12.6 Si) alloys

Effect of intermetallics on properties of Al-6.1Zn-2.3Mg-1.7Cu-0.15Zr-0.3Nd alloy: First-principles calculation

High-throughput design of high-performance lightweight high-entropy alloys

Achieving strength-ductility synergy in a novel Al-Mg-Zn-Cu-Si lightweight multi-component alloy via eutectic structure refinement