Abstract:A near-eutectic Al-Mg 2 Si-Mg alloy with high strength and toughness has been developed by adding 1.2-3.6 wt.% excess Mg (ΔMg) into Al-10Mg 2 Si alloy and systematically investigating the influences of ΔMg on the changes in the proportion of phases, microstructure characteristics, defect susceptibility, tensile properties, and fracture behavior of the alloy. The results indicate that with adding ΔMg content from 1.2 to 3.6 wt.%, the microstructure of the Al-10Mg 2 Si alloy transformed from hypoeutectic, near eutectic, then to hypereutectic characteristics. Moreover, the size of primary α-Al dendrites and SDAS values decrease accordingly as the ΔMg content increases from 0 to 2.8 wt.%. Furthermore, the addition of ΔMg could effectively refine the eutectic Mg 2 Si phase and change its 3D morphology from a clustered radial long plate-like bundle structure to a fine strip-like one. As a result, the strength and plasticity of the alloys have been significantly improved simultaneously. Among them, Al-10wt.%Mg 2 Si-2.8wt.%Mg near-eutectic alloy has the highest tensile properties, with YS, UTS, and EL values reaching 322.03 MPa, 117.42 MPa and 7.8%, which are 38.6%, 13.5% and 188.9% higher than the ΔMg-free alloy, respectively. Additionally, the addition of ΔMg resulted in the transitions of the solidification and tensile fracture mode of the alloys. The brittleness of Al-10wt.%Mg 2 Si alloy comes from the decohesion of coarse eutectic Mg 2 Si particles in the early stage of stretching, while the large amount of plastic deformation generated before the cracking of fine eutectic Mg 2 Si particles is responsible for the high strength and ductility of the Al-10wt.%Mg 2 Si-2.8wt.%Mg alloy. Furthermore, the preparation of the near-eutectic alloy will provide a reference for the development of other eutectic aluminum alloys with high strength and toughness for gravity casting.

Achieving strength-ductility synergy in a novel Al-Mg-Zn-Cu-Si lightweight multi-component alloy via eutectic structure refinement

Enhanced Strength–Ductility Synergy of Mg-Al-Sn-Ca Alloy via Composite Asymmetric Extrusion

Lightweight single-phase Al-based complex concentrated alloy with high specific strength

Microstructure, Phase Formation and Heat-Treating of Novel Cast Al-Mg-Zn-Cu-Si Lightweight Complex Concentrated Aluminum Based Alloy

Tailoring the heterophase interfacial structures to improve both strength and ductility of Al-Li alloys by fine tuning major solute Mg

Effects of electromagnetic stirring and subsequent homogenization treatment on the microstructure and mechanical properties of Al70Zn10Mg10Cu5Si5 multi-component alloy

Development of bimodal grain-structured Al-Zn-Mg-Cu-Zr alloys for strength-ductility synergy via microalloying with Hf and Sc

Achieving high strength via solutes co-clustering and solvents redistribution in an ultralightweight BCC magnesium alloy

Acquiring Mg-Ag microalloying TiB 2 /Al-4.5Cu composite simultaneously with ultrahigh strength and ductility via optimized salt-metal reaction and multistage heat treatment

Mechanistic investigation of a low-alloy Mg–Ca-based extrusion alloy with high strength–ductility synergy

Heterogeneous Lamella Design to Tune the Mechanical Behaviour of a New Cost-Effective Compositionally Complicated Alloy

Achieving strength-ductility synergy in Al-4.5 wt%Cu binary alloy through semisolid isothermal treatment coupled with ECAP

Improvement of Mechanical Behaviors of a Superlight Mg-Li Base Alloy by Duplex Phases and Fine Precipitates

Achieving synergy enhancement of strength and ductility in Ti-6Al-2Sn-4Zr-2Mo-0.1Si alloy by fabricating a new multiscale microstructure

Development of a Near Eutectic Al-Mg2Si-Mg Alloy with High Strength and Toughness

Computer Alloy Design of Ti Modified Al-Si-Mg-Sr Casting Alloys for Achieving Simultaneous Enhancement in Strength and Ductility

Simultaneous enhancement of strength and ductility by combining heterogeneous microstructure and nanoprecipitates

Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Achieving High Strength and Ductility in Magnesium Alloys via Densely Hierarchical Double Contraction Nanotwins

Enhanced strength and ductility in sand-cast Al-Li-Cu-Mg-Zr alloy via synergistic microalloying with Sc and Ti

Synergistic strengthening by β′′ and η′ phases in Al-Mg-Si-Cu-Zn alloys