Abstract:Composite micro-alloying is an important technique for developing cost-effective, high-performance aluminum alloys. Here, the effect of combined addition of Zr, Ti and rare-earth Y on the microstructure and tensile properties of an Al-7.6Zn-1.6 Mg-2.1Cu (wt.%) alloy is systematically investigated by means of X-ray diffraction, optical microscopy, scanning electron microscopy, transmission electron microscopy and room-temperature unixal tensile tests. After adding 0.12 %Zr, 0.04 %Ti and 0.28 %Y, L1 2 -Al 3 Zr/(Al,Zn) 3 Zr, AlMgZnTiCuFe and (Al,Zn) 8 Cu 4 Y phases were induced; the as-T6 treated microstructure of the base alloy changed from fully recrystallized to fully unrecrystallized, accompanied by strong 〈1 0 0〉 + 〈1 1 1〉 fiber textures along extrusion direction. As a result, the Al-Zn-Mg-Cu-Zr-Ti-Y alloy with low Zn and Mg contents exhibits an ultimate tensile strength of 692 MPa, yield strength of 647 MPa (∼36 % higher than the base alloy) and 6.8 % elongation. The main strengthening mechanisms responsible for this high yield strength are Orowan dislocation bypassing strengthening (∼449 MPa), fiber texture strengthening, and dispersion strengthening. Moreover, the synergistic strengthening effect of rare-earth Y and transitional element(s) Zr and/or Ti was revealed, which may be related to the formation(s) of nanoscale network-structured Al 8 Cu 4 Y and/or L1 2 -Al 3 (Zr,Y) phase(s). The massive formation of the Al 8 Cu 4 Y network structure requires a narrow process window.

Synergistic strengthening by β′′ and η′ phases in Al-Mg-Si-Cu-Zn alloys

Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Synergistic effect of gradient Zn content and multiscale particles on the mechanical properties of Al–Zn–Mg–Cu alloys with coupling distribution of coarse–fine grains

Disclosing Differential Precipitation Behavior of a Novel High Mg-containing Al-Mg-Zn-Si Alloy

Nanoscale Precipitates with Quasicrystal Domains Enhanced Strength-Ductility Synergy in a Mg–6Zn–4Al–1Sn–0.5Mn Alloy

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Insights into precipitation characteristics and strengthening mechanisms in a low Cu/Mg ratio Al-Cu-Mg-Ag alloy

Development of bimodal grain-structured Al-Zn-Mg-Cu-Zr alloys for strength-ductility synergy via microalloying with Hf and Sc

Mechanism for enhanced precipitation strengthening due to the addition of copper to Al-Zn-Mg alloys with high Zn/Mg ratio

Microstructure Evolution and Strengthening Mechanisms of Cast Al–Cu–Mn Alloy via Ti–Zr-Synergistic Micro-alloying

Achieving strength-ductility synergy in a novel Al-Mg-Zn-Cu-Si lightweight multi-component alloy via eutectic structure refinement

The microstructures and mechanical properties of a highly alloyed Al-Zn-Mg-Cu alloy: The role of Cu concentration

Enhanced strength-ductility synergy in an Al–Cu alloy via Cd-induced hybrid θ′′ + θ′ precipitation

Toward strength-ductility synergy in Al–Mg alloys: augmenting solute Mg concentration and strain-hardening ability via melt spinning and hot extrusion

Co-precipitation of T′ and η′ phase in Al-Zn-Mg-Cu alloys

Enhanced age-hardening by synergistic strengthening from Mg Si and Mg Zn precipitates in Al-Mg-Si alloy with Zn addition

Simultaneous enhancement of strength and ductility by combining heterogeneous microstructure and nanoprecipitates

Enhanced strength and ductility in sand-cast Al-Li-Cu-Mg-Zr alloy via synergistic microalloying with Sc and Ti

Ultra-high strength Al-Zn-Mg-Cu alloys with high zinc content prepared via powder hot extrusion

Significantly enhanced high-temperature mechanical properties of Cu-Cr-Zn-Zr-Si alloy with stable second phases and grain boundaries

Synergy of multiple precipitate/matrix interface structures for a heat resistant high-strength Al alloy