Abstract:Plastic injection molding is widely used in many industrial applications. Plastic products are mostly used as disposable parts or as portable parts for fast replacements in many devices and machines. However, mass production is always adopted as an ideal method to cover the huge demands and customers’ needs. The problems of warpage due to thermal stresses, non-uniform pressure distribution around cavities, shrinkage, sticking and overall products quality are some of the important challenges. The main objective of this work is to analyze the stress distribution around the cavities during the molding and demolding to avoid their effects on the product quality. Moreover, diagnosing the critical pressure points around and overall the cavity projection area, which is subjected to high pressure will help to determine the optimum pressure distribution and ensure filling all cavities at the same time, which is another significant objective. Computer-aided design (CAD) and CATIA V5R20 are adopted for design and modeling procedures. The computer-aided engineering (CAE) commercial software ABAQUS 6141 has been dedicated as finite element simulation packages for the analysis of this process. Simulation results show that stress distribution over the cavities depends on both pressure and temperature gradient over the contact surfaces and can be considered as the main affecting factor. The acceptable ranges of the cavity stresses were determined according to the following values: the cavity and core region temperature of 55–65 °C, filling time of 10–20 s, ejection pressure 0.85 % of injection pressure, and holding time of 10–15 s. Also, theoretical results reveal that the uniform pressure and temperature distribution can be controlled by adjusting the cavities layout, runner, and gate size. Moreover, the simulation process shows that it is possible to facilitate and identify many difficulties during the process and modify the prototype to evaluate the overall manufacturability before further investing in tooling. Furthermore, it is also concluded that tooling iterations will be minimized according to the design of the selected process

Restraint of Voids Generated Inside Injection Molded Products by In-Mold Pressing Method

Effect on Residual Wall Thickness of Parts with Floating Core Injection of Water-Assisted Injection Molding

Analysis of the main factors affecting mass production in the plastic molding process by using the finite element method

Influence of Processing Conditions on the Generation of Surface Defects in a Heat-and-Cool Hybrid Injection Molding Technique for Carbon Fiber-Reinforced Thermoplastic Sheets and Development of a Suitable Mold Heated by Far-Infrared Radiation

Research on Void Dynamics during In Situ Consolidation of CF/High-Performance Thermoplastic Composite

Optimization of the Compression (Injection/Compression) Molding Process Using Numerical Simulation

An Enhanced Vacuum-Assisted Resin Transfer Molding Process and Its Pressure Effect on Resin Infusion Behavior and Composite Material Performance

Experimental and numerical investigations on formation mechanisms of hollow structures in overflow water‐assisted injection‐molded parts of short‐glass‐fiber‐reinforced polypropylene

Effects of Heating and Cooling of Injection Mold Cavity Surface and Melt Flow Control on Properties of Carbon Fiber Reinforced Semi-Aromatic Polyamide Molded Products

Residual stresses, shrinkage, and warpage of complex injection molded products: Numerical simulation and experimental validation

Visualization Analysis of Defibration and Distributive Uniformity of Fibers in Long-fiber-reinforced, Injection-Molded Resins

Conventional and Microcellular Injection Molding of a Highly Filled Polycarbonate Composite with Glass Fibers and Carbon Black

Optimization of compression molding for double-concave lenses

Influence of process parameters and post-molding condition on shrinkage and warpage of injection-molded plastic parts with complex geometry

Numerical Simulation and Process Optimization of a 3D Thin-Walled Polymeric Part Using Injection Compression Molding

Pultrusion molding of continuous fiber reinforced thermoplastic composite pipe using partially-impregnated commingled yarns

Effect of Gas Counter Pressure on the Surface Roughness, Morphology, and Tensile Strength between Microcellular and Conventional Injection-Molded PP Parts

Effect of Mold Opening on Microcellular Polyether-Ether-ketone Fabricated by Injection Molding

Impact of Runner Size, Gate Size, Polymer Viscosity, and Molding Process on Filling Imbalance in Geometrically Balanced Multi-Cavity Injection Molding

Numerical Study of Thin-Walled Polymer Composite Part Quality When Manufactured Using Vacuum Infusion with Various External Pressure Controls

An experimental study on filling of gaps and void pockets during vacuum-bag-only consolidation of fiber placed preforms