Abstract:In the present work, the objectives were to investigate the type of microstructure and texture that developed after two step cold rolling — continuous annealing. Further, an attempt has been made to correlate the microstructure and texture with mechanical properties. Interstitial free (IF) and interstitial free — high strength (IF-HS) steel sheets which contain almost γ-fiber textures, were subjected to two step cold rolling for different percentage of reduction and further continuously annealed. It was observed that cold rolling strengthened the region of (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations of α-fiber as well as γ-fiber. After continuous annealing, cold rolled γ-fiber as well as (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations transformed to extremely strong new γ-fiber. It was found that at two steps 80% cold rolling -continuous annealing, drawability of IF steel sheet was exceptionally high i.e. around 3.15, whereas for IF-HS steel sheets, it was around 2.7. Although, two steps cold rolling -continuous annealing enhanced percentage elongation and stretchability exceptionally, but it reduced the yield strength substantially. However, ultimate tensile strength was hardly affected. In addition, it is also observed that two steps cold rolling — continuous annealing developed uniform grain size in both the grades of steel sheets.

Optimization of Annealing Parameters for Ferritic Hot-Rolled IF Grade Steel

Annealing Softening Behaviour of Cold-Rolled Low-Carbon Steel with a Dual-Phase Structure and the Resulting Tensile Properties

Grain Refinement and Texture Change in Interstitial Free Steels after Severe Rolling and Ultra-Short Annealing

An analysis of microstructure and mechanical properties of ferritic stainless steel 430 during cold rolling and subsequent annealing

Effect of two step cold rolling — continuous annealing on micro-structures, textures and mechanical properties in IF and IF-HS steel sheets

Effect of Annealing Temperature on Texture of Cold-Rolled IF Steel Rolled from Strip Hot-Rolled in Ferrite Region

The Influence of the Hot-Rolling Temperature on the Microstructure and Mechanical Properties of Ti-Nb Microalloyed 21%Cr Ferritic Stainless Steel

Annealing behaviour and mechanical properties of severely deformed interstitial free steel

Optimizing Microstructure and Mechanical Properties of Cold-Rolled Medium-Mn Steel Through Intercritical Annealing and Warm Rolling

Effects of Annealing Temperature on Microstructural Evolution and Mechanical Properties in Cold-Rolled High-Nitrogen Austenitic Steel

Effect of Annealing Temperature on Microstructure and Mechanical Properties of 00Cr21CuTi Stainless Steel Cold-Rolled Sheets

Effect of Cold Rolling Reduction Ratio on Microstructure and Mechanical Properties of Fe–10Mn–4Al-0.4C Steel Containing Δ Ferrite

Recrystallisation kinetics and yield-strength adjustment after annealing of cold-rolled microalloyed steel

An Investigation of Friction Coefficient on Microstructure and Texture Evolution of Interstitial-Free Steel during Warm Rolling and Subsequent Annealing

Effect of Coiling Temperature on Microstructure and Tensile Behavior of a Hot-Rolled Ferritic Lightweight Steel

Warm deformation and annealing behaviour of iron–silicon–(carbon) steel sheets

Effect of Annealing Process on Microstructure and Mechanical Properties of Super Fine Grain IF Steel

Influence of Heat Treatment on the Texture, Microstructure and Tensile Deformation Behaviours of Cold Rolled FeCoNiCr Sheets

Batch annealing production process of Ti-IF steel in Hansteel

Effect of Annealing Treatment on the Heterogeneous Microstructure and Properties of Cold-Rolled FeCoCrNiMn High-Entropy Alloy

Influence of Finish Rolling Temperature on Microstructure and Properties of Hot-Rolled SUS436L Stainless Steel