Abstract:In the present work, the objectives were to investigate the type of microstructure and texture that developed after two step cold rolling — continuous annealing. Further, an attempt has been made to correlate the microstructure and texture with mechanical properties. Interstitial free (IF) and interstitial free — high strength (IF-HS) steel sheets which contain almost γ-fiber textures, were subjected to two step cold rolling for different percentage of reduction and further continuously annealed. It was observed that cold rolling strengthened the region of (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations of α-fiber as well as γ-fiber. After continuous annealing, cold rolled γ-fiber as well as (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations transformed to extremely strong new γ-fiber. It was found that at two steps 80% cold rolling -continuous annealing, drawability of IF steel sheet was exceptionally high i.e. around 3.15, whereas for IF-HS steel sheets, it was around 2.7. Although, two steps cold rolling -continuous annealing enhanced percentage elongation and stretchability exceptionally, but it reduced the yield strength substantially. However, ultimate tensile strength was hardly affected. In addition, it is also observed that two steps cold rolling — continuous annealing developed uniform grain size in both the grades of steel sheets.

Effect of Cold Rolling on Texture and Microstructure Development in Annealed Incoloy 800 Fabricated Using Selective Laser Melting

Experimental selection of rolling contact length to the average thickness (L\have) ratio for producing fine-grain Incoloy 907 superalloy sheet by hot-rolling

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

Effect of Annealing on the Microstructure, Texture, and Properties of Cold-Rolled Ti50Ni47Fe3 Shape Memory Alloy Sheets

Effect of Cross-Rolling on the Hardness of the AlSi10Mg Alloy Fabricated through Powder Bed Fusion

Annealing behaviour and mechanical properties of severely deformed interstitial free steel

Revealing the inhomogeneous nature of microstructure and texture evolution in the cold-rolled CoCrFeMnNi alloy during static recrystallization

Microstructure, Texture, and Anisotropic Properties of High-Strength Low-Alloy Steel

Effect of two step cold rolling — continuous annealing on micro-structures, textures and mechanical properties in IF and IF-HS steel sheets

The Effects of Cold Rolling and Annealing on the Microstructure Evolution of Ordered C-2000 Alloy during Metallic Wire Preparation

Effect of Mode of Rolling on Recrystallization Kinetics and Microstructure Evolution in Interstitial Free High Strength Steel Sheet

Optimizing Tensile Properties and Hardness of Inconel 718 by Cold Rolling

The effect of cold rolling degree on microstructure, crystallographic texture and mechanical properties of Haynes® 282® wrought nickel superalloy

Severe warm-rolling mediated microstructure and texture of equiatomic CoCrFeMnNi high entropy alloy: A comparison with cold-rolling

Comparative analysis of cold and warm rolling on tensile properties and microstructure of additive manufactured Inconel 718

Effect of annealing temperature on the texture evolution and ovality of GH4145 alloy tubes with various numbers of rolling passes

Effect of cross cold rolling and annealing on microstructure and texture in pure nickel

RELEVANCE OF COLD-ROLLING TECHNOLOGY FOR THE TEXTURE AND ANISOTROPY OF EN AW-8011A ALUMINUM ALLOYS

Microstructure and Texture Evolution of Cold Rolled 1070 Al Alloy During the Subsequent Annealing Treatment

An Investigation of Friction Coefficient on Microstructure and Texture Evolution of Interstitial-Free Steel during Warm Rolling and Subsequent Annealing

Microstructure and Texture Evolution in Cold-Rolled and Annealed Oxygen-Free Copper Sheets