Abstract:In the present work, the objectives were to investigate the type of microstructure and texture that developed after two step cold rolling — continuous annealing. Further, an attempt has been made to correlate the microstructure and texture with mechanical properties. Interstitial free (IF) and interstitial free — high strength (IF-HS) steel sheets which contain almost γ-fiber textures, were subjected to two step cold rolling for different percentage of reduction and further continuously annealed. It was observed that cold rolling strengthened the region of (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations of α-fiber as well as γ-fiber. After continuous annealing, cold rolled γ-fiber as well as (223)[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] and 335[1\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\bar 1$$\end{document}0] orientations transformed to extremely strong new γ-fiber. It was found that at two steps 80% cold rolling -continuous annealing, drawability of IF steel sheet was exceptionally high i.e. around 3.15, whereas for IF-HS steel sheets, it was around 2.7. Although, two steps cold rolling -continuous annealing enhanced percentage elongation and stretchability exceptionally, but it reduced the yield strength substantially. However, ultimate tensile strength was hardly affected. In addition, it is also observed that two steps cold rolling — continuous annealing developed uniform grain size in both the grades of steel sheets.

Effect of Annealing Process on Microstructure and Mechanical Properties of Super Fine Grain IF Steel

Effect of Annealing on Microstructure and Corrosion Behavior of Interstitial Free Steel

Annealing behaviour and mechanical properties of severely deformed interstitial free steel

Effect of Annealing on the Microstructure, Texture, and Properties of Cold-Rolled Ti50Ni47Fe3 Shape Memory Alloy Sheets

Grain Refinement and Texture Change in Interstitial Free Steels after Severe Rolling and Ultra-Short Annealing

Effect of Annealing Treatment on Mechanical Properties of Nanocrystalline α-iron: an Atomistic Study

Effect of Annealing Process on Microstructure, Texture, and Mechanical Properties of a Fe-Si-Cr-Mo-C Deep Drawing Dual-Phase Steel

Influence of Annealing Time on Microstructure and Mechanical Properties of Al-14.5Si Alloy Prepared by Super-Gravity Solidification and Cold-Rolling

Microstructure, Texture, and Anisotropic Properties of High-Strength Low-Alloy Steel

Effect of Annealing Temperature on Microstructure and Mechanical Properties of 00Cr21CuTi Stainless Steel Cold-Rolled Sheets

Microstructure and Mechanical Properties of Low- and Medium-Carbon Si-Rich Low-Alloy Steels Processed by Austemping after Intercritical Annealing

The Influence of the Hot-Rolling Temperature on the Microstructure and Mechanical Properties of Ti-Nb Microalloyed 21%Cr Ferritic Stainless Steel

Effect of two step cold rolling — continuous annealing on micro-structures, textures and mechanical properties in IF and IF-HS steel sheets

Effect of annealing temperature on microstructure and properties of 1100 MPa grade cold-rolled dual-phase steel

An analysis of microstructure and mechanical properties of ferritic stainless steel 430 during cold rolling and subsequent annealing

Effect of annealing treatment on microstructure and mechanical properties of lightweight steels micro-alloyed with vanadium and niobium

Hall-Petch relationship of interstitial-free steel with a wide grain size range processed by asymmetric rolling and subsequent annealing

Effect of annealing temperature on microstructure and properties of a dual phase steel

Increase in Low-Carbon Steel 12GBA Strength and Cold Resistance by a Deformation-Thermal Effect

Tailoring Strength and Ductility of a Cr-Containing High Carbon Steel by Cold-Working and Annealing

Effect of microstructure modification on magnetic and mechanical properties of high-grade non-oriented silicon steel during annealing treatment