Abstract:Ferritic hot rolling of low carbon steel is now widely adopted by steelmakers for reducing energy costs and increasing the yield. These ferritic hot-rolled coils carry forward different grain morphology and texture which result in variation in properties after cold rolling and annealing compared to austenitic hot-rolled coils. These ferritic hot-rolled coils require different annealing treatments based on the hot rolling temperature for better results. In the present work, a Nb–Ti stabilized interstitial free (IF) grade steel was hot rolled at two different temperatures in the ferritic regime in an industrial hot strip mill and was subsequently cold rolled. These cold-rolled sheets were subjected to different continuous annealing cycles with soaking temperatures varying from 740 to 820 °C on a thermo-mechanical simulator for optimization of temperatures and study its effect on microstructure and properties. These coils were compared with simulated conventional austenitic hot-rolled coils. Ferritic rolled coils show better elongation and a higher percentage of equiaxed grains indicating better formability. The optimum continuous annealing temperature was found to be a function of hot rolling temperature in the ferritic regime. Elongation and grain size increased with an increase in temperature in all the samples, but the ferritic rolled coils show faster change due to higher stored energy. Comparison of elongation and microstructure indicates that temperatures above 780 °C should be sufficient for achieving complete recrystallization in ferritic rolled samples, compared to 810 °C required in the conventional austenitic rolled sheets which is an industrial advantage. Based on simulation studies, full-scale plant continuous annealing was carried out under the optimized temperature conditions where microstructure and properties matched closely with the simulation results and electron backscatter diffraction (EBSD) analysis confirmed improved texture.

Recrystallisation kinetics and yield-strength adjustment after annealing of cold-rolled microalloyed steel

Recrystallization Annealing Soaking Time Effect on the Tribological Behavior of Cold Upsetted Low Carbon Steel

Annealing Softening Behaviour of Cold-Rolled Low-Carbon Steel with a Dual-Phase Structure and the Resulting Tensile Properties

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Annealing behaviour and mechanical properties of severely deformed interstitial free steel

Grain Refinement and Texture Change in Interstitial Free Steels after Severe Rolling and Ultra-Short Annealing

Dilatometric study of continuous annealing of a cold‐rolled austenitic stainless steel

Tailoring Strength and Ductility of a Cr-Containing High Carbon Steel by Cold-Working and Annealing

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Influence of Microalloying Elements on Recrystallization Texture of Warm-Rolled Interstitial Free Steels

Microstructure evolution and compressive properties of a low carbon-low alloy steel processed by warm rolling and subsequent annealing

Study on dynamic recrystallization of ultra-high strength 22MnB5 steel during hot rolling

Thermomechanical and annealing processing effect on a rapid solidified Co – 20 wt. % Cr alloy

Effect of Cold Rolling Reduction Ratio on Microstructure and Mechanical Properties of Fe–10Mn–4Al-0.4C Steel Containing Δ Ferrite

Optimization of Annealing Parameters for Ferritic Hot-Rolled IF Grade Steel

Influence of Heat Treatment on the Texture, Microstructure and Tensile Deformation Behaviours of Cold Rolled FeCoNiCr Sheets

Warm deformation and annealing behaviour of iron–silicon–(carbon) steel sheets

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

Titanium‐Dependent Kinetics of Ferrite Single‐Phase Recrystallization in Cold‐Rolled Ultra‐High‐Strength Low‐Alloy Steels During Annealing

Effects of Annealing Temperature on Microstructural Evolution and Mechanical Properties in Cold-Rolled High-Nitrogen Austenitic Steel

Revealing the inhomogeneous nature of microstructure and texture evolution in the cold-rolled CoCrFeMnNi alloy during static recrystallization