Abstract:Spray-freeze-drying (SFD) is a process in which a solution is dispersed into a freezing medium and dried by sublimation, resulting in lyophilized powders with spherical particles. This study aims at screening and evaluating the impact of the excipient choice and spray solution characteristics in SFD on the physico-chemical characteristics of lyospheres and rate their suitability for producing pulmonary applicable powders using a novel SFD method. A monodisperse droplet-stream was injected into a vortex of cold gas for the production of inhalable, uniform spherical lyophilisates with a narrow particle size distribution. Model solutions containing graded contents (0.3%, 1.0%, and 3.0% w/v) of common bulk-forming excipients like mannitol, lactose, poylvinylpyrrolidone (PVP), maltodextrin or hydroyxpropyl methylcellulose (HPMC) and their blends were dispersed using a single 20 μm pinhole diaphragm. Powders were analyzed regarding their geometric particle size, apparent density, mechanical stability and aerodynamic performance. The diameter of the frozen droplets partially correlated with the Ohnesorge number of the spray solutions. The lyosphere powders had median geometric particle diameters ranging from 20 µm to 81 µm. Some powders showed signs of particle shrinkage during the drying step and diameters were reduced down to 30% of their initial size. The apparent particle densities ranged from 0.009 g/cm3 to 0.087 g/cm3. The mechanical stability of the lyospheres depended on the constituents and concentration of the initial spray solution. Mannitol/maltodextrin formulations yielded large porous particles with promising performance in the Next-Generation-Impactor, emitted fractions between 92 and 98% (w/w) and fine-particle-fractions of over 55% (w/w). According to our first steps towards formulations for free-flowing inhalable spray freeze-dried powders the impact of excipient choice on the SFD process is significant and based on the current findings we consider mannitol or mannitol/maltodextrin as best performing formulations.

Effect of foam spray drying process parameters on powder morphology

Particle morphology and powder properties during spray drying of maltodextrin and whey protein mixtures

Foam Structure Preservation during Microwave-Assisted Vacuum Drying: Significance of Interfacial and Dielectric Properties of the Bulk Phase of Foams from Polysorbate 80–Maltodextrin Dispersions

Influence of process conditions on the product properties in a continuous fluidized bed spray granulation process

Influence of drying conditions on layer porosity in fluidized bed spray granulation

Foam-mat drying of black soldier fly larvae: optimisation of foaming, drying kinetics, and powder characteristics

Effect of composition on physical properties of food powders

Impact of excipient choice on the aerodynamic performance of inhalable spray-freeze-dried powders

Modification on Drying Chamber Wall of Spray Dryer Towards Better Yield

Impact of formulation on reconstitution and flowability of spray-dried milk powders

Analysis of product properties in counter-current spray drying with two nozzles system

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene

Impact of processing parameters on the quality attributes of spray-dried powders: a review

Scalable preparation of hollow polymer and carbon microspheres by spray drying and their application in low-density syntactic foam

Effect of foaming agent concentration and drying temperature on biochemical properties of foam mat dried tomato powder

Spray-Drying of Alumina Powder for Aps: Effect of Slurry Properties and Drying Conditions Upon Particle Size and Morphology of Feedstock

Effects of formulation and processing parameters on the morphology of extruded polypropylene-(waste ground rubber tire powder) foams

Ultrasonic spray freeze-drying of sucrose and mannitol-based formulations: Impact of the atomization conditions on the particle morphology and drying performance

Comparison of blueberry powder produced via foam-mat freeze-drying versus spray-drying: evaluation of foam and powder properties

Development, Characterization and Process Optimisation of Foam- Mat Dried Tomato-Pepper-Onion Powder (TPOP Powder)

Tuning High and Low Temperature Foaming Behavior of Linear and Long-Chain Branched Polypropylene via Partial and Complete Melting