Abstract:Purpose The purpose of this paper is to quantitatively investigate the effect of process parameters (including welding current, voltage and speed) and plate thickness on in-plane inherent deformations in typical fillet welded joint; meanwhile, the plastic strains remaining in the weld zone are also analyzed under different influencing factors. Design/methodology/approach To achieve the purpose of this study, a thermal-elastic-plastic finite element (TEP FE) model is developed to analyze the thermal-mechanical behavior of the T-welded joint during the welding process. Experimental measurements have verified the validity of the established TEP FE model. Using the effective model, a series of numerical experiments are performed to obtain the inherent deformations under the conditions of different influencing factors, and then the calculation results are discussed based on the relevant data obtained. Findings Through numerical simulation analysis, it is found that the longitudinal and transverse inherent deformations decrease with the increase of welding speed and plate thickness, whereas as the nominal heat input increases, the inherent deformations increase significantly. The longitudinal shrinkage presents a quasi-linear and nonlinear distribution in the middle and end of the weld, respectively. The plastic strains in the cross section of the T-joint also vary greatly because of the process parameters and plate thickness, but the maximum value always appears near the location of the welding toe, which means that this point faces a relatively large risk of fatigue cracking. The inherent deformations are closely related to the plastic strains remaining in the weld zone and are also affected by many influencing factors such as process parameters and plate thickness. Research limitations/implications In this study, relatively few influencing factors such as welding current, voltage, speed and plate thickness are considered to analyze the inherent deformations in the T-welded joint. Also, these influencing factors are all within a certain range of parameters, which shows that only limited applicability can be provided. In addition, only in-plane inherent deformations are considered in this study, without considering the other two out-of-plane components of inherent deformations. Originality/value This study can help to expand the understanding of the relationship between the inherent deformations and its influencing factors for a specific form of the welded joint, and can also provide basic data to supplement the inherent deformation database, thereby facilitating further researches on welding deformations for stiffened-panel structures in shipbuilding or steel bridges.

Study on welding crack sensitivity assessment method based on thermal elastic plastic finite element analysis

Numerical simulation of influence factors of stress distribution of weld-bonded joint under peeling load

An Insight into the Creep-Fatigue Damage Localization in Welded Joints Based on Crystal Plasticity Finite Element Method

Fatigue reliability assessment of welded joints in steel bridges considering multiple effects

Numerical analysis about dependence relation between plastic zone spread direction for welded joints with interface crack and mixity angle of composite material

Study on Welding Sequence of Butt-Welded Structures Based on Equivalent Heat Source Parameter

On the Method for Evaluating the Sensitivity to Reheat Cracking in the Weld Zone of Steel

Numerical Study on Influence of Rupture Strain on Crack Driving Force of Welded Joints with Damage

C * estimation for cracks in mismatched welds and finite element validation

Effect of Inhomogeneous Mechanical Properties on the Stress-Strain Field at the Crack Tip and Crack Growth Direction in Dissimilar Metal Welded Joints

STUDY ON DIRECT EVALUATION OF J-INTEGRAL OF SURFACE CRACK IN WELDMENTS

Cyclic elastoplasticity-based life assessment of fatigue crack initiation and subsequent propagation in rib-to-deck welded joints

Investigation of the Quality Category Approach for BS7910-based Rapid Fatigue Assessment of Welded Structures Containing Cracks

The Effect of Process Parameters and Plate Thickness on In-Plane Inherent Deformations in T-joint Fillet Weld

Analysis of Crack Propagation of Annular Butt Weld and Distribution of Weld-Induced Residual Stress

Experimental and computational analysis of residual buckling distortion of bead-on-plate welded joint

Study on fracture mechanics parameters of surface crack in overmatched weldments

Numerical Studies of Estimation of Fracture Parameters for Mismatched Welded Joints with HAZ Cracks

Study of Welding Inherent Deformations in Thin Plates Based on Finite Element Analysis Using Interactive Substructure Method

Predicting Welding Residual Stress of a Multi-pass P92 Steel Butt-Welded Joint with Consideration of Phase Transformation and Tempering Effect

Effect of Yield Strength Distribution Welded Joint on Crack Propagation Path and Crack Mechanical Tip Field