Abstract:In this paper, we present a systematic study of the as-cast and heat-treated microstructures of three refractory metal intermetallic composites based on Nb (i.e., RM(Nb)ICs), namely the alloys EZ2, EZ5, and EZ6, and one RM(Nb)IC/RCCA (refractory complex concentrated alloy), namely the alloy EZ8. We also examine the hardness and phases of these alloys. The nominal compositions (at.%) of the alloys were Nb-24Ti-18Si-5Hf-5Sn (EZ2), Nb-24Ti-18Si-5Al-5Hf-5Sn (EZ5), Nb-24Ti-18Si-5Cr-5Hf-5Sn (EZ6), and Nb-24Ti-18Si-5Al-5Cr-5Hf-5Sn (EZ8). All four alloys had density less than 7.3 g/cm3. The Nbss was stable in EZ2 and EZ6 and the C14-NbCr2 Laves phase in EZ6 and EZ8. In all four alloys, the A15-Nb3X (X = Al,Si,Sn) and the tetragonal and hexagonal Nb5Si3 were stable. Eutectics of Nbss + Nb5Si3 and Nbss + C14-NbCr2 formed in the cast alloys without and with Cr addition, respectively. In all four alloys, Nb3Si was not formed. In the heat-treated alloys EZ5 and EZ8, A15-Nb3X precipitated in the Nb5Si3 grains. The chemical compositions of Nbss + C14-NbCr2 eutectics and some Nb5Si3 silicides and lamellar microstructures corresponded to high-entropy or complex concentrated phases (compositionally complex phases). Microstructures and properties were considered from the perspective of the alloy design methodology NICE. The vol.% Nbss increased with increasing ΔχNbss. The hardness of the alloys respectively increased and decreased with increasing vol.% of A15-Nb3X and Nbss. The hardness of the A15-Nb3X increased with its parameter Δχ, and the hardness of the Nbss increased with its parameters δ and Δχ. The room-temperature-specific strength of the alloys was in the range 271.7 to 416.5 MPa cm3g-1. The effect of the synergy of Hf and Sn, or Hf and B, or Hf and Ge on the macrosegregation of solutes, microstructures, and properties of RM(Nb)ICs/RCCAs from this study and others is compared. Phase transformations involving compositionally complex phases are discussed.

Modification of hypereutectic Al-Si alloy surface layer structure by Nb alloying under high temperature plasma impact

Modification of Surface Mechanical Properties of Aluminum by Nb Ion Implantation

Microstructure and Mechanical Properties of Spark Plasma Sintered CoCrFeNiNbX High-Entropy Alloys with Si Addition

On the Microstructure and Properties of the Nb-23Ti-5Si-5Al-5Hf-5V-2Cr-2Sn (at.%) Silicide-Based Alloy—RM(Nb)IC

Alkali-Heat Treatment of A Low Modulus Biomedical Ti-27nb Alloy

A Study of the Effects of Hf and Sn on the Microstructure, Hardness and Oxidation of Nb-18Si Silicide-Based Alloys-RM(Nb)ICs with Ti Addition and Comparison with Refractory Complex Concentrated Alloys (RCCAs)

Formation and properties of niobium silicide coatings on Nb-Ta alloy substrate

High-Temperature Oxidation Behavior of Plasma Surface Nb-Cr-(Si) Alloying System on γ-TiAl

Nanocrystalline Nb coating deposited on etched sapphire substrate by plasma alloying technique

Structure and Phase Composition of WNb Alloy Formed by the Impact of Compression Plasma Flows

Formation and Precipitation Phases of Ni-Al System Intermetallic Surfacing Layers by Light Beam Heating

NbC TRANSFORMATION DURING AGING IN HP40-Nb HEAT RESISTANT ALLOY

Fracture Behavior and Mechanism of Nb-Si-Based Alloys with Heterogeneous Layered Structure

Effect of Microstructure and Performance of Nb–Cr–Fe–Ni Quaternary Alloys with the Variation of Niobium Element Content

Ti–Nb–Si-based surface alloy fabricated on TiNi SMA substrate through additive electron beam method: structure and perspectives

Microstructure Evolution and Toughening Mechanism of a Nb-18Si-5HfC Eutectic Alloy Created by Selective Laser Melting

Synthesis of Nb3Al high temperature intermetallic compound by laser deposition

Structure and Properties of a High-Entropy AlCrFeCoNi Alloy after Treatment with an Electron–Ion Plasma

Microstructural and mechanical evaluation of Nb-silicide-based in situ composite at ultrahigh temperature

Change of surface structure of thin silicon nitride layers during electron beam rapid thermal annealing

Influence of Laser Power on Microstructure of Nb-16Si Binary Alloys Fabricated by In-situ Additive Manufacturing