Abstract:The superconducting magnet group at IHEP (the Institute of High Energy Physics, Chinese Academy of Sciences, China) has been engaging in the R&D of high field accelerator magnets since 2014 for the pre-study of the next-generation high energy particle accelerators like CEPC-SPPC (Circular Electron Positron Collider-Super Proton Proton Collider), FCC (Future Circular Collider), etc. A superconducting model dipole magnet named LPF1 was first fabricated with NbTi and Nb3Sn in a combined common-coil configuration in 2017 and tested in 2018, a main field of 10.23 T was reached within two 10 mm apertures. The magnet was reassembled with higher pre-stress in 2019 to investigate the influence of the pre-stress loading level on the performance of common-coil dipole magnets. The main field of this upgraded magnet named LPF1-S was increased to 10.71 T within two 12 mm apertures. By improving the key processing technologies in Rutherford cable fabrication, coil winding, Nb3Sn & NbTi splices soldering and coil impregnation, the recently fabricated model dipole magnet named LPF1-U attained a 12.47 T main field in two 14 mm apertures in 2021. To fully take advantage of Nb3Sn and NbTi superconductors in different field regions, LPF1-U was still designed and developed with a combined coil configuration with Nb3Sn for the inner two coils and NbTi for the outer four coils. Additionally, graded coil topology and different coil LSS (length of straight section) settings were adopted in the optimization of LPF1-U layouts. Bladder and key technology was used for the support structure, and fiber optic sensors based on FBG (fiber Bragg grating) were utilized to monitor the stress distribution and variation in the structures and coils through the whole process from magnet assembly to cool-down and excitation. During the performance test, a relatively large number of trainings were carried out and LPF1-U became more stable after the thermal cycle. A peak field of 12.7 T in the coils (12.47 T main field in apertures) corresponds to an operating current of 6865 A and a load line ratio of 90% was finally attained. It is worth mentioning that LPF1-U is the first hybrid-Nb3Sn, NbTi-common coil dipole magnet that has achieved a main field of more than 12 T in two apertures. The design, fabrication and performance analysis of the LPF series dipole magnets are presented in this paper.

Superconducting multipole wiggler with large magnetic gap for HEPS-TF

Design and Fabrication of a 13-T Twin-Aperture Superconducting Dipole Magnet with Graded Common-Coil Configuration

Development of a Conduction-Cooled HTS SMES

Development of Superconducting Model Dipole Magnets Beyond 12 T with a Combined Common-Coil Configuration

Mechanical Design, Assembly and Strain Measurement Results of a 13-T Superconducting Dipole Magnet

Design and Testing of a Prototype Canted-Cosine-Theta HTS Dipole Magnet Using CORC Cable

Design and Performance of the First Dual-Coil Magnet at the Wuhan National High Magnetic Field Center

Concept Design of 100 T Pulsed Magnet at the Wuhan National High Magnetic Field Center

Design and testing of a demonstration HTS diploe magnet

The Conceptual Optimal Design of a 300MJ High Temperature Superconducting Magnet

Conceptual Design of CEPC Detector Magnet

Fabrication Procedures and Mechanical Supports of No-Insulation All-GdBCO Double Pancake Magnets in Liquid Helium

Design of a large-scale superconducting dipole magnet for the CEE spectrometer

Mitigating Radiation Impact on Superconducting Magnets of the Higgs Factory Muon Collider

Structural design and test of superconducting magnet coil for the cooling storage ring external-target experiment

Design, Development and Fabrication for BESIII Superconducting Muon Detector Solenoid

Development of a 1/2-length prototype high field Nb3Sn magnet for the 4th generation ECR ion source

Design and Test of a 90-T Nondestructive Magnet at the Wuhan National High Magnetic Field Center

Development of short prototype of dual aperture quadrupole magnet for CEPC ring

Progress in the Construction of a 20 T REBCO Insert Coil for High-Field All-Superconducting Magnets

High Temperature Superconducting YBCO Insert for 25 T Full Superconducting Magnet