Abstract:Purpose The purpose of this paper is to conduct a comparative study of the surface modifications induced by two different lasers on a 2050‐T8 aluminum alloy, with a specific consideration of residual stress and work‐hardening levels. Design/methodology/approach Two lasers have been used for Laser shock peening (LSP) treatment in water‐confined regime: a Continuum Powerlite Plus laser, operating at 0.532 mm with 9 ns laser pulses, and near 1.5mm spot diameters; a new generation Gaia‐R Thales laser delivering 10 J‐10 ns impacts, with 4‐6mm homogeneous laser spots at 1.06 mm. Surface deformation, work‐hardening levels and residual stresses were analyzed for both LSP conditions. Residual stresses were compared with numerical simulations using a 3D finite element (FE) model, starting with the validation of surface deformations induced by a single laser impact. Findings Similar surface deformations and work‐hardening levels, but relatively lower residual stresses were obtained with the new large 4‐6 mm impact configuration. This was attributed to a reduced number of local cyclic loadings (2) compared with the small impact configuration (4). Additionally, more anisotropic stresses were obtained with small impacts. FE simulations using Johnson‐Cook's material' behavior were shown to simulate accurately surface deformations, but to overestimate maximum stress levels. Research limitations/implications This work should provide LSP workers a better understanding of the possible benefits from the different LSP configurations currently co‐existing: using small ( 4‐5 mm). Moreover, experimental results and simulated data had never been presented on 2050‐T8 Al alloy. Originality/value An experimental (and numerical) comparison using two distinct laser sources for LSP, has never been presented before. This preliminary work should help LSP workers to choose adequate sources.

Modeling of multi-edge effects in the case of laser shock loadings applied on thin foils: Application for material characterization of aluminum alloys

Analysis of laser shock waves and resulting surface deformations in an Al–Cu–Li aluminum alloy

Laser shock processing with two different laser sources on 2050‐T8 aluminum alloy

Investigation on Laser-Induced Shock Pressure with Condensed Matter Model and Experimental Verification

Subsurface hardening of Al irradiated with ultrafast infrared laser

Laser shock processing of aluminium alloys. Application to high cycle fatigue behaviour

Dynamic response and roughness control of surface materials on TC4 titanium alloy subjected to laser shock wave planishing

The Effect of Viscous Drag on the Maximum Residual Stresses Achievable in High-Yield-Strength Materials in Laser Shock Processing

Numerical and experimental investigation of laser shock microhydroforming technology for microforming thin-walled LA103Z alloy foil with complex microfeatures

Numerical and Experimental Investigation on Pulsed Nanosecond Laser Ablation Processing of Aluminum Alloy

Investigation of the Effect of Laser Treatment on the Longitudinal and Transverse Velocity of an Aluminum Alloy

Laser-induced softening analysis of a hardened aluminum alloy by physical simulation

Numerical Simulation Study of Laser-Driven Shock Wave Propagation in Planar Al Foil Targets

Crystal Plasticity Modeling of Laser Peening Effects on Tensile and High Cycle Fatigue Properties of 2024-T351 Aluminum Alloy

Computational Modeling and Experimental Validation of Thermal Stress and Melt Pool Characteristics Using High Power Laser Diode Beam on 7075 Aluminum Alloy

Prediction of Residual Stress Random Fields for Selective Laser Melted A357 Aluminum Alloy Subjected to Laser Shock Peening

Preparation and Laser Damage Mechanism of Stray-Light-absorbing Thin Films in High-Energy Laser Systems

High shock release in ultrafast laser irradiated metals: Scenario for material ejection

CFD modeling for predicting imperfections in laser welding and additive manufacturing of aluminum alloys

Effects of sacrificial coating material in laser shock peening of L-PBF printed AlSi10Mg

Nonlinear analysis model of the progressive damage of aluminum–wood sandwich structures under high-speed impact conditions