Abstract:Purpose The purpose of this paper is to conduct a comparative study of the surface modifications induced by two different lasers on a 2050‐T8 aluminum alloy, with a specific consideration of residual stress and work‐hardening levels. Design/methodology/approach Two lasers have been used for Laser shock peening (LSP) treatment in water‐confined regime: a Continuum Powerlite Plus laser, operating at 0.532 mm with 9 ns laser pulses, and near 1.5mm spot diameters; a new generation Gaia‐R Thales laser delivering 10 J‐10 ns impacts, with 4‐6mm homogeneous laser spots at 1.06 mm. Surface deformation, work‐hardening levels and residual stresses were analyzed for both LSP conditions. Residual stresses were compared with numerical simulations using a 3D finite element (FE) model, starting with the validation of surface deformations induced by a single laser impact. Findings Similar surface deformations and work‐hardening levels, but relatively lower residual stresses were obtained with the new large 4‐6 mm impact configuration. This was attributed to a reduced number of local cyclic loadings (2) compared with the small impact configuration (4). Additionally, more anisotropic stresses were obtained with small impacts. FE simulations using Johnson‐Cook's material' behavior were shown to simulate accurately surface deformations, but to overestimate maximum stress levels. Research limitations/implications This work should provide LSP workers a better understanding of the possible benefits from the different LSP configurations currently co‐existing: using small ( 4‐5 mm). Moreover, experimental results and simulated data had never been presented on 2050‐T8 Al alloy. Originality/value An experimental (and numerical) comparison using two distinct laser sources for LSP, has never been presented before. This preliminary work should help LSP workers to choose adequate sources.

Subsurface hardening of Al irradiated with ultrafast infrared laser

Analysis of laser shock waves and resulting surface deformations in an Al–Cu–Li aluminum alloy

Laser shock processing of aluminium alloys. Application to high cycle fatigue behaviour

Laser shock processing with two different laser sources on 2050‐T8 aluminum alloy

Comparison of surface integrity of GH4169 superalloy after high-energy, low-energy, and femtosecond laser shock peening

Quantification of room temperature strengthening of laser shock peened Ni-based superalloy using synchrotron microdiffraction

Numerical investigation on spall fracture in a metallic material caused by laser shock peening

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

Laser Shock Peening of Ti6Al4V Alloy with Combined Nanosecond and Femtosecond Laser Pulses

The effect of laser shock processing on the microstructures and properties of 2060 Al Li alloys

Comparison of Mechanical and Corrosion Properties of 7050 Aluminum Alloy after Different Laser Shock Peening

Laser shock-processing for fatigue and fracture resistance

High shock release in ultrafast laser irradiated metals: Scenario for material ejection

Thermal fatigue crack growth behavior of ZCuAl10Fe3Mn2 alloy strengthened by laser shock processing

Effect of Preliminary Heat Treatment on the Formation of Structure and Residual Stresses in the AMg6 Alloy at Laser Shock Peening Without Coating

In situ X-ray tomography of fracture behaviour in low-porosity L-PBF AlSi10Mg alloy with laser shock peening

Abnormal Softening of Ti-metallic Glasses During Nanosecond Laser Shock Peening

Influence of pulse energy on surface integrity of AZ31 magnesium alloy processed by femtosecond laser shock peening

Molecular dynamics simulation of microstructural evolution and mechanical behavior of titanium alloy subjected to laser shock peening

Effect of layer-wise femtosecond laser shock peening on cracking growth in laser powder bed fused AA 7075

Laser shock peening regulating aluminum alloy surface residual stresses for enhancing the mechanical properties: Roles of shock number and energy