Abstract:Ti2AlNb alloy is a new type of lightweight and heat-resistant structural material that has been an active research topic with multi-phases due to its improved mechanical properties. However, the phase response under severe plastic deformation (SPD) at high strain rates is unclear, which limits the understanding of its strengthening mechanism. Here, laser shock peening (LSP) was employed to investigate the microstructure response of alpha 2, O, and B2/beta phases in Ti2AlNb alloy. After LSP, the highest density dislocations were generated in the B2/beta phases, followed by the O phases, and the least dislocations were observed in the alpha 2 phases. In the B2/beta phases, only dislocation tangles (DTs) were observed. Dislocation lines (DLs) and DTs were mainly distributed in the O phases. As for the alpha 2 phases, DLs were generated while a small number of DTs were piled up at the grain boundaries. In addition, parallel dislocations (PDs) with a spacing of about 135 nm can be observed on the surface of the alpha 2 phases, and the dislocations interspersed between PDs were composed of screw dislocations with long segments. In addition to dislocation structures, stacking faults (SFs) were observed in both alpha 2 phases and O phases, and mechanical twins were formed in the O phases, which were generated to coordinate the SPD induced on the surface. These dislocation structures formed dislocation cells (DCs) and sub-grain boundaries which further developed into high-angle grain boundaries (HAGBs) together with mechanical twins, dividing the coarse grains and refining the microstructure. As the depth increased, the responses of the three kinds of phases decreased. The PDs in the alpha 2 phases have widened spacing and could not penetrate the grains. The mechanical twins were gradually reduced until no obvious twin structure could be observed. Finally, dislocations, grain size, microhardness, and residual stress presented a gradient distribution. The improved microhardness (maximum 470 HV) and compressive residual stress (maximum -600 MPa) which were consistent with the refined grains and highdensity dislocations gradually decreased to that of the base metal (BM).

Abnormal Softening of Ti-metallic Glasses During Nanosecond Laser Shock Peening

Effect of laser-shock peening on the structure and nano-mechanical behavior of a Ti-based metallic glass

Rejuvenation, Embryonic Shear Bands and Improved Tensile Plasticity of Metallic Glasses by Nanosecond Laser Shock Wave

Laser Shock Peening of Ti6Al4V Alloy with Combined Nanosecond and Femtosecond Laser Pulses

Microstructure evolution and mechanical properties of a lamellar near-α titanium alloy treated by laser shock peening

Magnetic Field‐Assisted Laser Shock Peening of Ti6Al4V Alloy

Unveiling the origins of work-hardening enhancement and mechanical instability in laser shock peened titanium

Numerical investigation on spall fracture in a metallic material caused by laser shock peening

High energy laser-shock induced phase transformation and micro-spallation on surface of stainless steels: The effect of stacking fault energy and deformation mechanisms

Quantification of room temperature strengthening of laser shock peened Ni-based superalloy using synchrotron microdiffraction

Molecular dynamics simulation of microstructural evolution and mechanical behavior of titanium alloy subjected to laser shock peening

Laser shock processing of titanium alloys: a critical review on the microstructure evolution and enhanced engineering performance

Carbide-facilitated nanocrystallization of martensitic laths and carbide deformation in AISI 420 stainless steel during laser shock peening

Gradient microstructure response in different phases of Ti<sub>2</sub>AlNb alloy with laser shock peening

Microstructure evolution and electroplasticity in Ti64 subjected to electropulsing-assisted laser shock peening

Dislocation pinning effects induced by nano-precipitates during warm laser shock peening: Dislocation dynamic simulation and experiments

Studies on Laser Shock Peening on Nanomechanical and Mechano-Chemical Properties of Titanium Alloy (Ti6Al4V)

Plastic deformation behavior of titanium alloy by warm laser shock peening: Microstructure evolution and mechanical properties

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

Laser shock peened Ti-6Al-4 V alloy: Experiments and modeling

Laser shock peening-induced misfit dislocation at interfaces between HCP and BCC crystals of Ti6Al4V alloy and the corresponding dislocation patterns in two phases