Abstract:High performance polymer-fiber composites are high strength, low weight materials that have many applications, many of which would benefit from a decrease in weight, without a decrease in material properties. Generally, the fibers serve as the main load carriers, while the matrix serves to distribute load and protect the fibers from the environment. Thus, it is postulated that if the volume fraction of matrix is reduced, while still ensuring complete wetting of the fibers by the matrix, the per unit weight, i.e., specific, mechanical properties could be improved. This can be done by introducing small, spherical bubbles. Given the small average inter-fiber distance and assuming that the bubbles must not interact with the surface of the reinforcements the bubble diameter would need to be less than 1 μm. Introducing bubbles this small and ensuring that they do not form, or become attached, on the surface of the reinforcement are significant challenges. Two methods to produce such bubbles and the effect of these bubbles on mechanical properties of neat resins are reviewed: the addition of hollow spherical fillers, called microballoons, and the creation of bubbles from blowing agents. Microballoons in resins are a class of materials called syntactic foams. Although commercial microballoons are too large, smaller diameters can be made and could be used to reduce the weight of a reinforced composite on the order of 10%. The use of a physical blowing agent to produce bubbles in a composite is also considered. However, traditional polymer foaming techniques may be inadequate, as nucleation on the reinforcing phase is likely, and the bubbles formed are generally too large, so the use of blowing agent wells is considered. Blowing agent wells are discontinuous regions made from copolymer micelles or immiscible polymers that act as reservoirs of blowing agent. Additionally, the use of nano-sized materials for use as heterogeneous nucleation sites and secondary reinforcement of the matrix is also considered. Bubbles made from blowing agent could reduce the weight slightly more than using hollow spheres, but the reduction would also be of the order of 10%.

Epoxy-Glass Microballoon Syntactic Foams: Rheological Optimization of the Processing Window

Transport Properties of One-Step Compression Molded Epoxy Nanocomposite Foams

Processing of Hollow Glass Microspheres (HGM) filled Epoxy Syntactic Foam Composites with improved Structural Characteristics

New Insights on Expandability of Pre-Cured Epoxy Using a Solid-State CO2-Foaming Technique

Synthesis and characterization of foams generated via gel state frontal polymerization

Tensile, Thermal and Dynamic Mechanical Properties of Hollow Polymer Particle-Filled Epoxy Syntactic Foam

Effect of Hollow Glass Microspheres Surface Modification on the Compressive Strength of Syntactic Foams

Lightweight epoxy foams prepared with arranged hollow-glass-microspheres/epoxy hollow spheres

Effects of silane coupling agent modifications of hollow glass microspheres on syntactic foams with epoxy matrix

Fabrication of syntactic foam fillers <i>via</i> integrated on/off-chip microfluidic methods for optimized geopolymer composites

Co-continuous hollow glass microspheres/epoxy resin syntactic foam prepared by vacuum resin transfer molding

Reactive Molecular Dynamics Simulation of Epoxy for the Full Cross-Linking Process

A review of the feasibility of lightening structural polymeric composites with voids without compromising mechanical properties

Effect of the Aromatic Amine Curing Agent Structure on Properties of Epoxy Resin-Based Syntactic Foams

Compressive properties of co-continuous hollow glass microsphere/epoxy resin syntactic foams prepared using resin transfer molding

Fabrication of syntactic foam fillers <i>via</i> manipulation of on-chip quasi concentric nanoparticle-shelled droplet templates

Preparation, Characterization, and Mechanical Properties of Microcellular Poly(Aryl Ether Ketone) Foams

Effect of particle stiffness and surface properties on the nonlinear viscoelasticity of dense microgel suspensions

The Effects of a Crosslinking Agent on the Microrheological Properties and Cellular Structure of Silicone Rubber Foam Prepared via a Green Process

Synthesis and Characterisation of Floatable Magnesium Alloy Syntactic Foams with Hybridised Cell Morphology

Crosslinked Epoxy Microspheres: Preparation, Surface-Initiated Polymerization, And Use As Macroporous Silica Porogen