Abstract:Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal–vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR > TSR > VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology was used to study how the initial residual stress in the blank causes the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method was applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method was used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters was studied.

Ring-core integral method to measurement residual stress distribution of Al-7075 alloy processed by cyclic close die forging

Finite Element Simulation Analysis on Residual Stress Relief of 7075 Aluminum Alloy Ring

Evaluation of Residual Stress Depth Profiling in 7075 Aluminum Alloy Plates

Evaluation of residual stress relief of aluminum alloy 7050 by using crack compliance method

Effect of Cold Pressing Deformation on Microstructure and Residual Stress of 7050 Aluminum Alloy Die Forgings

Numerical Simulation and Experiment of Stress Relief and Processing Deformation of 2219 Aluminum Alloy Ring

Research on machining deformation of aluminum alloy rolled ring induced by residual stress

Numerical modeling and experimental assessment of dynamic behavior of aluminum alloy 7075-T6 in machining process

A Forward Identification Method for High-Temperature Stress-Strain Curves of 7075 Aluminum Alloy Sheet Considering the Necking Stage

Deformation Behavior and Microstructure of 6061 Aluminum Alloy Processed by Severe Plastic Deformation Using Biaxial Alternate Forging

Numerical simulation of stress evolutions in 2A14 aluminum alloy components during solution and aging process

Cyclic Deformation Behavior of A Heat-Treated Die-Cast Al-Mg-Si-Based Aluminum Alloy

Cyclic Extrusion Compression Process for Achieving Ultrafine-Grained 5052 Aluminum Alloy with Eminent Strength and Wear Resistance

Effect of thermomechanical processing on mechanical properties and microstructural evolution of Al-Mg-Zn alloy

Damage in Creep Aging Process of an Al-Zn-Mg-Cu Alloy: Experiments and Modeling

Effects of heat treatment on a novel continuous casting direct rolling 6056 aluminum alloy: cold rolling characteristics and tensile fracture properties

Reducing Residual Stress in 7050 Aluminum Alloy Die Forgings by Heat Treatment

Correlation Characteristics of the Deformation Relief of an Aluminum Alloy Under High-Cycle Fatigue

The improvement of deformability in AA7075 alloy through cryogenic treatment and its correlation with microstructural evolution and FE modelling

Investigation of an L-Shaped Cross-Sectioned AA6061 Aluminum Alloy Ring via Extrusion and Self-Bending Integral Processing Technology

Numerical and Experimental Research on Cold Compression Deformation Method for Reducing Quenching Residual Stress of 7A85 Aluminum Alloy Thick Block Forging