Abstract:Conductive polymer composites (CPCs) exhibit favorable density and corrosion resistance for application as bipolar plate (BP) in proton exchange membrane fuel cell (PEMFC). However, achieving CPCs that combine the required level of electrical conductivity and mechanical strength is a challenge that has limited their application in PEMFC BPs. This study explored the potential of achieving CPC BPs with high electrical and mechanical performance by using carbon black (CB) as a secondary filler in graphite-polymer composites. Polypropylene (PP)/epoxy blend was selected as the matrix due to its good combination of strength and toughness as well as its potential to form a co-continuous morphology, which promotes the formation of more continuous conducting networks within the composite, leading to enhanced electrical performance. The PP/epoxy/graphite/CB composites were prepared by melt mixing in a Rheomixer at 190 °C and 60 rpm for 10 min, followed by compression molding at 200 °C and 6 metric tonnes for 10 min. The electrical conductivity of the composites increased from 49.26 Scm−1 to 90.34 Scm−1 (in-plane) and from 0.37 Scm−1 to 9.34 Scm−1 (through-plane) as the total filler content increased from 50 to 85 wt%. The flexural strength initially increased from 45.57 MPa at 50 wt% to 51.84 MPa at 60 wt% total filler content. Further increase in total filler content led to a decrease in flexural strength. The nanosize CB particles, used as a minor filler, filled the voids between the graphite particles, leading to the formation of more conducting pathways and higher electrical conductivities compared to the PP/epoxy/graphite composites without CB fillers. The PP/epoxy/graphite/CB composite with 80 wt% total filler content exhibited the most promising in-plane conductivity (88.5 Scm−1), through-plane conductivity (8.52 Scm−1), and flexural strength (28.53 MPa) for BP application.

High-Performance Fluorinated Ethylene-Propylene/Graphite Composites Interconnected with Single-Walled Carbon Nanotubes

Structure and Properties of Carboxylated Carbon Nanotubes@Expanded Graphite/Polyethersulfone Composite Bipolar Plates for PEM

High performance polyvinylidene fluoride/graphite/multi-walled carbon nanotubes composite bipolar plate for PEMFC with segregated conductive networks

Improved Performance of Composite Bipolar Plates for PEMFC Modified by Homogeneously Dispersed Multi-Walled Carbon Nanotube Networks Prepared by In Situ Chemical Deposition

Electrical and mechanical properties of polypropylene/epoxy blend-graphite/carbon black composite for proton exchange membrane fuel cell bipolar plate

Electrical conductivity enhancement of chopped carbon fiber‐reinforced epoxy composite bipolar plate for proton exchange membrane fuel cells

Development of novel composite bipolar plates using surface‐modified conductive carbon filler materials for polymer electrolyte membrane fuel cells

Composite Materials Based on Thermally Expanded Graphite for Fuel Cell's Bipolar Plates

Effect of Secondary Carbon Nanofillers on the Electrical, Thermal, and Mechanical Properties of Conductive Hybrid Composites Based on Epoxy Resin and Graphite

Achieving high electrochemical performance of PEMFCs with ultrathin and highly conductive graphite-resin composite bipolar plates

Muti-Filler Composites Reinforced with Multiwalled Carbon Nanotubes and Chopped Carbon Fibers for the Bipolar Plate of Fuel Cells

Collective Enhancements on Thermal-Electrical and Mechanical Properties of Graphite-Based Composite Bipolar Plates through the Coupled Manipulations of Molding and Impregnation Pressures

Preparation and Performance Study of PEK‐C‐OH/MWCNT‐COOH/Graphite Composite Bipolar Plates for PEMFCs With Improved Interface Properties

Low filler and highly conductive composite bipolar plates with synergistic segregated structure for enhanced proton exchange membrane fuel cell performance

Fabrication of Electrically Conductive Polymer Composites for Bipolar Plate by Two‐step Compression Molding Technique

Reviewing carbon nanotube fillers for enhanced conductivity in proton exchange membrane fuel cell bipolar plates

High-performance polybenzoxazine based composites PEMFC bipolar plates with a multi-layer structure for surface enrichment of conductive phase

Preparation and properties of graphite/polypropylene composite material reinforced by chopped carbon fibers for proton‐exchange membrane fuel cell bipolar plates

Use of Ni/CNT Particles as Additive Fillers in Ebonite Bipolar Plates for Proton-Exchange Membrane Fuel Cells

Fumed Silica Additives Enables Tunable Wettability of the Resin for Improved Composite Bipolar Plate

Carbon Black Doped Graphite Composite Bipolar Plate Compounds for Improving Conductivity