Abstract:Bi 2 Te 3 -based materials can be assembled into promising thermoelectric generators (TEGs) used for room temperature applications, yet their regulation for a wide range of applications, like the Internet of Things (IoTs), is limited by the small open circuit voltage, poor output power and large energy loss resulting from parasitic depletion to some extent. In this work, we have fabricated high-density thermoelectric generators (HD-TEGs) to compensate for these shortages, and the boosted voltage could reduce the energy loss simultaneously. To integrate HD-TEGs, the fabrication processes manipulate electrode deposition and reflow soldering techniques of delivering micro- and bulk-TEGs. Subsequently, a normalized power density of ∼13.7 μW cm −2 K −2 , along with an open circuit voltage of ∼1.9 V, calculated contact depletion of ∼36% and experimental circuit depletion of ∼5% at Δ T of 13 K, has been achieved in a HD-TEG with 338 thermocouples (Tcs). Upon increasing Δ T to 73 K, the open circuit voltage and maximum output power are ∼10.1 V and 843.2 mW, which exceed those of the 50-Tcs TEG with packing fraction ( f ) of 5% and 34%, as well as the 200-Tcs TEG ( f = 20%). These conversion properties are even much better than those of most commercial TEGs. Further, the finite-element simulation data indicate that output power and open circuit voltage could be further optimized to ∼68.5 mW (25.4 μW cm −2 K −2 ) and ∼2.9 V at Δ T of 13 K, by further increasing the density of thermoelectric elements and reducing contact loss. Moreover, our study elucidates that fabricating TEGs by using a high-density approach, i.e. , optimizing packing fraction by increasing the quantity of thermocouples, could be an effective avenue for achieving high output performance with superior critical voltage and small energy loss.

Silicon integrated circuit thermoelectric generators with a high specific power generation capacity

Operating Temperature Dependency of Power Generation Capacity in Silicon Planar-Integrated Microthermoelectric Generators

Design, Fabrication, and Characterization of CMOS MEMS-Based Thermoelectric Power Generators

Si and SiGe Nanowire for Micro-Thermoelectric Generator: A Review of the Current State of the Art

Optimizing the output performance and parasitic depletion of Bi2Te3-based thermoelectric generators by using a high-density approach

Development of MEMS Process Compatible (Bi,Sb)2(Se,Te)3-Based Thin Films for Scalable Fabrication of Planar Micro-Thermoelectric Generators

On‐Chip Thermoelectric Devices Based on Standard Silicon Processing

High Power Density Micro Thermoelectric Generators for Powering IoTs

A High Power Density Micro-Thermoelectric Generator Fabricated by an Integrated Bottom-Up Approach

High-Performance Wearable Bi2Te3-Based Thermoelectric Generator

Seal and Encapsulate Cavities for Complementary Metal-Oxide-Semiconductor Microelectromechanical System Thermoelectric Power Generators

No external load measurement strategy for micro thermoelectric generator based on high-performance Si1−x−yGexSny film

Wafer-level vacuum sealing and encapsulation for fabrication of CMOS MEMS thermoelectric power generators

Transitioning from Si to SiGe Nanowires as Thermoelectric Material in Silicon-Based Microgenerators

Development of Cu2Se/Ag2(S,Se)-Based Monolithic Thermoelectric Generators for Low-Grade Waste Heat Energy Harvesting

Planar-type silicon thermoelectric generator with phononic nanostructures for 100 μW energy harvesting

Micro-thermoelectric Devices with Large Output Power Fabricated on a Multi-Channel Glass Template

Planar-type SiGe thermoelectric generator with double cavity structure

Silicon nanowires as efficient thermoelectric materials

Single-Crystal Silicon Thermoelectrics by Phonon Engineering

Micro thermoelectric devices: From principles to innovative applications