Abstract:This paper presents a multi-gain radio frequency (RF) front-end low noise amplifier (LNA) utilizing a multi-core based on the source degeneration topology. The LNA can cover a wide range of input and output frequency matching by using a receiver (RX) switch at the input and a capacitor bank at the output of the LNA. In the proposed architecture here, to avoid the saturation of RX chain, 12 gain steps including positive, 0 dB, and negative power gains are controlled by a mobile industry processor interface (MIPI). The multi-core architecture offers the ability to control the power consumption over different gain steps. In order to avoid the phase discontinuity, the negative gain steps are provided using an active amplification and T-type attenuation path that keeps the phase discontinuity below ±5 degrees between two adjacent power gain steps. Using the multi-core structure, the power consumption is optimized in different power gains. The structure is enhanced with the adaptive variable cores and reactance parameters to maintain different power consumption for different gain steps and remain the output matching in an acceptable operating range. Furthermore, auxiliary linearization circuitries are added to improve the input third intercept point (IIP3) performance of the LNA. The chip is fabricated in 65 nm complementary metal-oxide semiconductor (CMOS) silicon on insulator (SOI) process and the die area is 0.308 mm2. The proposed architecture achieves the IIP3 performance of -10.2 dBm and 8.6 dBm in the highest and lowest power gains, which are 20.5 dB and -11 dB, respectively. It offers the noise figure (NF) performance of 1.15 dB in the highest power gain while it reaches 14 dB when the power gain is -11 dB. The LNA consumes 16.8 mA and 1.33 mA current from a 1 V power supply that is provided by an on-chip low-dropout (LDO) when it operates at the highest and lowest gains, respectively.

Design and analysis of 0.9 and 2.3‐GHz concurrent dual‐band CMOS LNA for mobile communication

Analysis and Design of Ultra-Wideband Low-Noise Amplifier with Input/Output Bandwidth Optimization and Single-Ended/Differential-Input Reconfigurability.

Analysis and Design of Wideband Low Noise Amplifier with Digital Control

Analysis And Design Of Inductorless Wideband Low-Noise Amplifier With Noise Cancellation Technique

A Compact 2.1–39 GHz Self-Biased Low-Noise Amplifier in 65 Nm CMOS Technology

A dual-band 2.1GHz/5.2GHz LNA for reconfigurable radio

A 28-/39-ghz Dual-Band CMOS LNA with Shunt-Series Transformer Feedback

A 24–30 GHz CMOS LNA with 2.05db NF and 0.6db In-Band Gain Ripple for 5G-Applications

Optimal Design of 2.4 GHz ISM Band CMOS LNA Using the Cat Swarm Optimization Algorithm

A 22.9–38.2-Ghz Dual-Path Noise-Canceling LNA with 2.65–4.62-Db NF in 28-Nm CMOS

A 20-44 GHz Wideband LNA Design Using the SiGe Technology for 5G Millimeter-Wave Applications

Low Noise Amplifier Design and Performance Analysis of RF Front-End for Narrow Band Receivers

Wideband Inductorless Low-Power LNAs with Gm Enhancement and Noise-Cancellation.

A 7.2–27.3 GHz CMOS LNA With 3.51 ±0.21 dB Noise Figure Using Multistage Noise Matching Technique

A dual band CMOS two-stage variable gain low noise amplifier

A mm‐wave LNA employing current re‐use and non‐linearity cancellation in 28 nm CMOS for automotive RADAR and 6G receivers

A 22-32.7 GHz Linearized LNA in 65-nm CMOS Using Multigate Transistor Technique

A Broadband CMOS LNA for WLAN Applications

A 30‐ghz Low‐power CMOS LNA for 5G Communication Systems

A 1.8-2.7 GHz Triple-Band Low Noise Amplifier with 31.5 dB Dynamic Range of Power Gain and Adaptive Power Consumption for LTE Application

A High Gain Fully Integrated CMOS LNA for WLAN and Bluetooth Application