Abstract:Remote, terrestrial, and space sensors require sources that have high enough power and energy densities for continuous operation for multiple decades. Conventional chemical sources have lower energy densities and lifetimes of 10 to 15 years depending on environmental conditions. Betavoltaic (βV) nuclear batteries using β‐‐emitting radioisotopes possess energy densities approximately 1000 times greater than conventional chemical sources. Their electrical power density (Pe,vol in W/cm3) in a given volume is a function of β‐‐flux surface power density , surface interface type between radioisotope and transducer, β‐ range, and transducer thickness and conversion efficiency (ηs). Tritium is the most viable β‐‐emitting radioisotope because of its commercial availability, low biotoxicity, half‐life, and low energy, which minimizes the penetration depth and damage of transducer. To maximize Pe,vol, tritium in solid or liquid form must be used in the βV nuclear battery. A Monte Carlo source model using MCNP6 was developed to maximize the Pe,vol of a tritium‐based βV nuclear battery. First, a planar coupling configuration with different tritiated compounds (ie, titanium tritide and tritiated nitroxide) and a semiconductor transducer (4H‐SiC) with thicknesses of 1 and 100 μm were modeled. The results showed that β‐‐source efficiency (ηβ), which is the percentage of energy deposited in the transducer, decreased as the tritiated compound's mass density increased. The highest Pe,vol was dependent on a combination of characteristics: specific activity (Am in Ci/g), mass density, and 4H‐SiC layer thickness. The tritiated nitroxide with the highest Am at 2372 Ci/g produced the highest Pe,vol at 2.46 mW/cm3. Second, a 3‐D coupling configuration was modelled to increase surface interfacing between the radioisotope source and textured transducer surface. 3‐D coupling configuration increased the percentage of energy deposited into the transducer because of more surface interfacing between the transducer and source in the same volume. The tritiated nitroxide was selected as the radioisotope source coupled with five different textured surface feature types. The Pe,vol as a function of textured surface feature and gap, where the radioisotope is located, width was calculated for 1‐ and 100‐μm 4H‐SiC layer thicknesses. Results showed that ηβ increased compared with planar coupling configuration (ie, approximately 56.2% increase over planar with cylindrical hole array) except with the rectangular pillar array. Still, the rectangular pillar array produced the highest Pe,vol at 4.54 mW/cm3 with an increasing factor of 2.29 compared with the planar coupling configuration.

Investigation of nickel‐63 radioisotope‐powered GaN betavoltaic nuclear battery

Researches on the performance of GaN-PIN betavoltaic nuclear battery

Performance study of GaN-based betavoltaic nuclear batteries with 3D interfaces

Research on the Performance of Nuclear Battery with SiC-Schottky and GaN-PIN Structure

Investigation on beta voltaic effect based on one-dimensional TiO2 nanotube array thin film

A nuclear battery based on silicon p-i-n structures with electroplating 63Ni layer

Structural design and optimization of 3D interface structures based on betavoltaic nuclear batteries

Design and Fabrication of a 63ni Thin Film Source for a 63Ni-Si Betavoltaic Battery

Growth and fabrication of GaN/AlGaN heterojunction bipolar transistor

Theoretical study of a high-efficiency GaP–Si heterojunction betavoltaic cell compared with metal–Si Schottky barrier betavoltaic cell

Theoretical prediction of time-related performance of GaN-based p–n junction betavoltaic battery

Theoretical prediction of output performance of 63NiO-Si heterojunction betavoltaic cell

Betavoltaic Enhancement Using Defect-Engineered TiO2 Nanotube Arrays Through Electrochemical Reduction in Organic Electrolytes

Study of the Electroless Deposition of Ni for Betavoltaic Battery Using PN Junction without Seed Layer

Electron Beam Irradiation of Gallium Nitride-on-Silicon Betavoltaics Fabricated with a Triple Mesa Etch

An experimental apparatus for study of direct β-radiation conversion for energy harvesting

Design and Simulation of High Conversion Efficiency Betavoltaic Battery Based on a Stacked Multilayer Structure

Enhancing betavoltaic nuclear battery performance with 3D P+PNN+ multi-groove structure via carrier evolution

Fabrication of SiC P-I-n Betavoltaic Cell with 63ni Irradiation Source

Planar and textured surface optimization for a tritium‐based betavoltaic nuclear battery

A Novel Betavoltaic Microbattery Based on SWNTs Thin Film-Silicon Heterojunction