Abstract:Abstract. Accurate knowledge of the input torque in wind turbine gearboxes is key to improving their reliability. Traditionally, rotor torque is measured using strain gauges bonded to the shaft. Transferring the resulting signal from the rotating shaft to a stationary data acquisition system while powering the sensing devices is complex and costly. The magnitude of the torques involved in wind turbine gearboxes and the high stiffness of the input shaft pose additional difficulties. This paper presents a new alternative method to measure the input torque in wind turbine gearboxes based on deformation measurements of the static first stage ring gear. We have measured deformation using fiber optic strain sensors based on fiber Bragg gratings because of their advantages compared to conventional electrical strain gauges. The present study was conducted on a Siemens Gamesa Renewable Energy gearbox with a rated power of 6MW, in which a total of 54 fiber optic strain sensors were installed on the outer surface of the first stage ring gear. The gear mesh forces between the planets and the ring gear cause measurable deformations on the outer surface of the stationary ring gear. The measured strains exhibit a dynamic behavior. The strain values change depending on the relative position of the strain sensors to the planet gears, the instantaneous variations of the input torque, and the way load is shared between planets. A satisfactory correlation has been found between the strain signals measured on the static ring gear and torque. Two signal processing strategies are presented in this paper. The first procedure is based on the peak-to-peak strain values computed for the gear mesh events, and therefore, torque can only be estimated when a gear mesh event is detected. The second signal processing procedure combines the strain signals from different sensors using a Coleman coordinate transformation and tracks the magnitude of the fifth harmonic component. With this second procedure, it is possible to estimate torque whenever strain data of all sensors is available, leading to an improved frequency resolution up to the sampling frequency used to acquire strain data. The method presented in this paper could make measuring gearbox torque more cost-effective, which would facilitate its adoption in serial wind turbines and enable novel data-driven control strategies, as well as a more accurate assessment of the consumed fatigue life of the gearboxes throughout their operation.

Influences on torque measurement in nacelle test benches and their effect on the measurement uncertainty and consequences of a torque calibration

Proposals for a practical calibration method for mechanical torque measurement on the wind turbine drive train under test on a test bench

Research and Application of Dynamic Torque Calibration for Torque Test Bench of Electric Actuator in Nuclear Power Plant

Study of a 2 kN·m Torque Transducer Tested at GUM and PTB, Including Creep Behaviour

Validation of a Non-Contact Technique for Torque Measurements in Wind Turbines Using an Enhanced Transient FSV Approach

Further Work on Analyzing Accuracy and Overall Performance of Torque Tools for Assembling Bolted Flanged Joints

Force calibration using errors-in-variables regression and Monte Carlo uncertainty evaluation

Non-intrusive torque measurement for rotating shafts using optical sensing of zebra-tapes

The study of in-situ calibration technology of redocking torque parameter of performance test system for space station redocking mechanism

Input Torque Measurements for Wind Turbine Gearboxes Using Fiber Optical Strain Sensors

From Strain to Loads: Development of a Measurement Solution for Wind Turbine Transmission Input Loads during Drivetrain Testing

Measurement uncertainty evaluation of a hexapod-structured calibration device for multi-component force and moment sensors

A Calibration Strategy for EV Drives Based on Improved MTPV Table Decoupled from Permanent Magnet Flux Linkage Variation

Design and Calibration of a Torque Sensor Based on Sectional Redundant Measurements.

Experimental verification of predicted capability of a wind turbine drivetrain test bench to replicate dynamic loads onto multi-megawatt nacelles

Torque Estimation for Robotic Joint with Harmonic Reducer Based on Deformation Calibration

Recent advances in mechanical torque studies of small-scale magnetism

Measurement of the jet deflector torque for model pelton turbine and associated uncertainties in test rig development

A Performance Test Rig and Its Measuring System for Centripetal Turbines of Micro-Gas-Turbines

Torque measurement for researching the energy characteristics of electric vehicle drives

Experimental Investigation Of Torque Measurement In Hermetic Compressor