Abstract:Resonance is an important failure mechanism that arises when a periodic force acts at a frequency corresponding to a blade natural frequency. If the damping is inadequate for absorption of the periodic input energy, amplitude and stresses grow until failure occurs by overstress or by propagation of fatigue crack. A complex and irregular distribution of minor indentations covers the surface, including leading edge impacts. The damage caused by foreign objects often in the form of a geometric discontinuity like a notch. However the presence of residual stress and sub-structural damage in regions adjacent to the notch prohibit the use of simple notch analyses. FE analysis is used to estimate stress concentration effect of the geometry of the notch. For this purpose, the compressor aerofoil blade is idealized into simple rectangular cantilever plate for FEM study. The complexity of the problem is reduced to a simplex problem by assuming the aerofoil section to a flat rectangular plate. Because of the nonpresence of the aerofoil section, analysis is so simple for finding the stress concentration effect of the geometrical notch made. To analyze the stress concentration effect of foreign object damage (FOD), different notches are made by varying the notch dimensions viz., depth, radius of the notch and the location of the notch on the trailing edge of the rectangular plate. Foreign object damaged compressor blades with nicks, dents and cracks can be ground into the smooth curved cutouts to reduce the stress intensification and stress concentration with a high speed grinding wheel. In doing so, depending on the extent and type of damage, designer has a requirement to estimate size and shape of the cut-out to be made on the aerofoil that generates the known SCF. With the estimated values of SCF for different geometry of cut using FEM further a modal analysis has been conducted to assess the variation of frequencies for different geometry of cut-outs with known values of SCF to aster the correctness of the solution, the finite element analysis is carried out on a rectangular cantilever plate for which literature is available. Further the study is extended to an idealized problem of Abstract: Modal analysis has been important to the designers and operators since the inception of the Turbo machinery. Blades typically fail because of low-cycle fatigue (LCF), and high-cycle fatigue (HCF), environmental attack, Creep, Oxidation, erosion, embrittlement. In the present work the turbine blade is modeled and analyzed using finite element method the eigen value extraction for flexural and torsional modes is obtained. Foreign object damage is simulated by considering a circular crack along the leading edge of the blade. It was found that the stretching induced by the centrifugal inertia force due to the rotational motion of the blades was the cause for the increment of the bending stiffness of the structure. This resulted in maximum operational Vonmises stresses; the object is to provide understanding and information for designers to improve the life and efficiency of gas turbines.

Untwist Creep Analysis of Gas Turbine First Stage Blade

Degradation Behavior of Microstructures and Mechanical Properties of GTD111 Turbine Blade After Long-Term Service

Creep life prediction for a nickel-based single crystal turbine blade

Evaluation of Gas Turbine Hot Section Blade Cracking under Oxidation, TMF, and Creep Conditions

A Hybrid Modeling Method of Fatigue Crack Growth for Gas Turbine Blades under Combined High and Low Cycle Fatigue Loadings

Creep analysis and service life prediction of turbine blade with progressive damage

Structural Analysis of Gas Turbine Blade

Computer simulation of a rotor creep

Technique for Estimating the Residual Life of Gas Turbine Engine Blades under High-Temperature Creep

Direct Investigation on High Temperature Tensile and Creep Behavior at Different Regions of Directional Solidified Cast Turbine Blades

Methodology for estimation of residual life of turbine blades of gas turbine engine under high-temperature creep condition

Modeling And Analysis Of Flexural And Torsional Modes Of Gas Turbine Blades Considering The Foreign Object Damage

A Dynamic Systems Based Approach to Estimate Cyclic and Creep Damage of a Power Turbine Blade Subjected to a Random Transient Operation

Creep-Based Reliability Evaluation of Turbine Blade-Tip Clearance with Novel Neural Network Regression

Multiaxial creep–fatigue failure mechanism and life prediction of a turbine blade based on a unified numerical solution approach

Failure Investigation of a Kaplan Turbine Blade

Failure assessment of braided ceramic matrix composite dovetail turbine blade under thermo-mechanical load

An entropy-based failure prediction model for the creep process

High temperature creep property of a novel porous double layer cooling structure for gas turbine blades

Influence of Simplifications of Blade in Gas Turbine on Film Cooling Performance

Vibration Analysis of Tapered Pre-Twisted Functionally Graded Rotating Blade