Abstract:The performance of follow-on experiments using irradiated nuclear fuel at any point in its lifecycle is a critical step in understanding phenomena and behavior. Transient experiments with high-burnup fuel can deepen the understanding of fuel fragmentation, relocations, and dispersal under loss-of-coolant accidents. An advanced autonomous welding process to refabricate commercial fuel rods inside a hot cell was created and tested to enable flexible experiment approaches on fuels irradiated in commercial and test reactors. Irradiated light water reactor fuel test pins from experiments performed at the Advanced Test Reactor (ATR) at Idaho National Laboratory were used to demonstrate the refabrication process. The welding process was found to be sensitive to welding parameters but flexible such that multiple passes could be performed on the same location until a hermetic weld was obtained. The refabrication of rodlets and successful welds was also found to be sensitive to the preparation of the irradiated cladding and endcaps. Thorough defueling of the fuel at the weld location and proper sizing of the endcaps and backing material mitigated these issues. The use of strategically located heat sinks in contact with the cladding and endcap materials also increased welding and refabrication success. For this work, the test pins were sectioned to remove the original endcaps and fuel was removed from both ends of each rodlet. The reassembly of the rodlets was then completed in four steps, which included the press fitting of new endcaps, the circumferential welding of rodlet endcaps to the cladding, rodlet pressurization in a pressure chamber, and seal welding the rodlet under pressure. The integrity of the refabricated rodlets was then verified via helium leak checking inside a vacuum chamber. The advanced welding system is capable of refabricating rodlets up to 380 mm in length, and repressurizing them up to 15 500 kPa. The refabricated lengths of the rodlets used in this work ranged from 149 to 165 mm and the refabricated fuel stack heights ranged from 70.4 to 79.8 mm. The rodlets were pressurized with argon to an average pressure of 3617 kPa, and the average leak rate after refabrication was 6.7∙10 −8 ∙cm 3 ∙s −1 .

Auxiliary Beam Stress Improved Laser Welding for Repair of Irradiated Light Water Reactor Components

ICONE19-43939 Phenomenological Evaluation of Laser-Irradiated Welding Processes with a Combined Use of Higher-Accuracy Experiments and Computational Science Methodologies : (5) Numerical Simulation of the Welding Processes with a Multi-Dimensional Multi-Physics Analysis Code SPLICE

A novel pathway for multiscale high-resolution time-resolved residual stress evaluation of laser-welded Eurofer97

G010023 Numerical Simulation for Phenomenological Evaluation of Laser Welding Processes

Irradiation-assisted cracking of SA508-304L weldments with 308L groove filler and 309L butter in hot water immersion constant rate extension tests

Advanced Autonomous Welding for Refabrication and Follow-On Testing of Previously Irradiated Nuclear Fuel

Improving the strength-ductility synergy and corrosion resistance of Inconel 718/316L dissimilar laser beam welding joint via post-weld heat treatment

Development of microstructure and residual stress in electron beam welds in low alloy pressure vessel steels

Significantly improved weldability in laser welding of additively manufactured Haynes 230 superalloys by tailoring microstructure

Understanding the Mechanism of Stress Corrosion Cracking Resistance in Stainless Steel Welds Subjected to Laser Shock Peening without Coating for Nuclear Canister Applications

Optimization of a Welding Procedure for Making Critical Aluminum Welds on the LBNF Absorber Core Block

Effect of Post Weld Heat Treatment on the Microstructure and Properties of Laser-TIG Hybrid Welded Joints for CLAM Steel

Three-Dimensional Numerical Simulation of Repairing Process by Laser Direct Energy Deposition

Finite element analysis of CFRP and stainless steel laser welding

A Comparative Study on the Performance and Microstructure of 304NG Stainless Steel in Underwater and Air Laser Welding

Microstructure and mechanical properties of friction stir weld performed on neutron-irradiated 304L steel with helium

Mitigation of Tensile Residual Stress Induced During Welding with Laser Shock Processing

Quarter Century Development of Laser Peening without Coating

Effect of Dynamic Preheating on the Thermal Behavior and Mechanical Properties of Laser-Welded Joints

Study of Mechanical Properties, Microstructure, and Residual Stresses of AISI 304/304L Stainless Steel Submerged Arc Weld for Spent Fuel Dry Storage Systems

Development of electron optical capabilities for manufacturing of large components by electron beam welding