Abstract:The CH-Structure has been studied at the IAP Frankfurt and at GSI for several years. Compared with the IH structure (110-mode), the CH structure (210-mode) can operate at higher frequencies (150 700 MHz) and can accelerate ions to higher energies (up to 150 AMeV). Detailed Microwave Studio (MWS) simulations were performed for this structure. Since a multi-gap cavity can be approximated as a quasi-periodic structure, it is possible to analyse one βλ/2-cell at an energy corresponding to the cavity centre. A reduced copper conductivity of 85% was adopted in effective shunt impedance calculations. Geometry variations with respect to RF frequency and shunt impedance can be performed rapidly by that method in the first stage of optimization. Using the transit time factor calculated by the beam dynamics simulation code LORASR, effective shunt impedances from 100 MΩ/m down to 45 MΩ/m were obtained for the energy range from 6MeV to 66 MeV by this method. The RF frequency was 352 MHz. A systematic analysis of the influence of the cell number in long CH-cavities on the effective shunt impedance is presented. Actually, a 70 MeV, 70 mA, 352 MHz proton linac design for GSI Darmstadt is developed. About 12 CH-cavities will cover the energy range from 3 MeV up to the final energy, the DTL total length will be around 22m. INTRODUCTION The Interdigital H-type (IH) structure is well known for its high shunt impedance at low beta values. It is successfully used as front part for ion linacs like the Unilac at GSI [1] or the CERN Linac3 [2] and for rare isotope acceleration. Since a couple of years, a new type of H-structure was proposed and studied at IAP, Frankfurt and GSI, Darmstadt, that is the Cross Bar H-type (CH) structure. Compared with the IH-structure, the CHstructure is providing new features. Working in the H21 mode, the transverse cavity dimensions are significantly larger than that of the IH-cavity at a given frequency and velocity profile, thus it can work at higher frequencies up to around 700 MHz. This allows to close the velocity gap with respect to attractive structures at the low energy end of Coupled Cavity Linacs CCL. It can be designed for operation at about 350 MHz in the first section and at 700 MHz in the high-energy section up to about 150 AMeV. Furthermore, the CH cavity exceeds by far the mechanical rigidity of the IH cavity. This opens the possibility to develop superconducting multi-cell cavities as well [3]. A set of formulas based on a simple field model was derived for H-type structures to describe the main RF parameters as a function of the geometrical dimensions. A normal conducting 70 MeV, 70 mA proton injector based on a 3 Mev RFQ followed by a CH-DTL is designed for the future FAIR facility at GSI. The beam dynamics [4] and the cavity design are studied in parallel. The construction of a model cavity will start this year. In the following sections we present the results got from cavity simulations for room temperature CH structures, the emphasis is put on the effective shunt impedance.

Beam commissioning of the demonstrator setup for the superconducting continuous wave HIM/GSI-Linac

Continuous wave interdigital H-mode cavities for alternating phase focusing heavy ion acceleration

A dynamic collimation and alignment system for the Helmholtz linear accelerator

The beam commissioning of a CW high charge state heavy ion RFQ

Commissioning Status of the Linac for the Facility for Rare Isotope Beams

Commissioning of the laser-driven ion acceleration beamline at the Centre for Advanced Laser Applications

High-power test results for a cylindrical-shell silicon carbide higher-order-mode damper

Construction and commissioning of a technological prototype of a high-granularity semi-digital hadronic calorimeter

Design Parameters and Commissioning of Vertical Inserts Used for Testing the XFEL Superconducting Cavities

Design, Fabrication, and Beam Commissioning of A Continuous-Wave Four-Rod Rf Quadrupole

Magnet Design for the High-Intensity Muon Beams Project (HIMB) at PSI's Accelerator Complex HIPA

Installation, commissioning, and testing of the HB650 CM at PIP2IT

Achievement of high-current continuous-wave deuteron injector for Linear IFMIF Prototype Accelerator (LIPAc)

Design of the r . t . ch-cavity and perspectives for a new gsi proton linac *

Status of Higher Order Mode Beam Position Monitors in 3.9 GHz Superconducting Accelerating Cavities at FLASH

Beam Commissioning Status and Results of the FNAL PIP2IT Linear Accelerator RFQ

Beam physics design of a superconducting linac

Advances of the FRIB Project

Probing the losses for a high power beam

Beam Commissioning of the Coupled RFQ-SFRFQ Cavity

Stable Acceleration of a LHe-Free Nb3Sn demo SRF e-linac Based on Conduction Cooling