Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Low-Temperature Features of the Micromechanical Properties of Polystyrene

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Glass Transition Temperature of Polystyrene Microparticles

Study of Elastic Modulus and Yield Strength of Polymer Thin Films Using Atomic Force Microscopy

Glass Transition of Atactic Polystyrene with Less Chain Entanglements

Low-Temperature Radiation-Induced Conductivity of Polystyrene under the Action of Low-Energy Electrons

Investigating Mechanical Response of Single Chain Polystyrene Particles by Scanning Probe Techniques

Ultrasonic characterization of polymer viscoelasticity. Application to polystyrene

Glass Transition Temperature in Polystyrene Supported Thin Films: a SPM-based Investigation of the Role of Molecular Entanglement

Onset of Plasticity in Thin Polystyrene Films

Temperature-induced Evolution of Micro-structure and Chain Dynamics in Thermoplastic Polyurethane with Low Hard Segment Content as Studied by In Situ Synchrotron SAXS and Time-Domain NMR Experiments

Theory of low-temperature elasticity of amorphous polymers: Deformation at a constant rate and relaxation of deforming stress

Strain Rate-Regulated Sub-Rouse Transition in Polystyrene Via Dynamic Mechanical Spectroscopy

Thermomechanical coupling during large strain deformation of polycarbonate: Experimental study

Strain Rate and Temperature Influence on Micromechanisms of Plastic Deformation of Polyethylenes Investigated by Positron Annihilation Lifetime Spectroscopy

On the Cryogenic “degradation” of Polystyrene in Dilute Solution

Thermal Behaviors of Polystyrene Plasticized with Compressed Carbon Dioxide in A Sealed System

Rubbery layer on polystyrene surface well below the glassy temperature

DYNAMIC MECHANICAL RESPONSE OF CRAZES IN POLYSTYRENE *

Surface properties of hydroxy-terminated polystyrenes

Thermal and Rheological Analysis of Polystyrene-Grafted Silica Nanocomposites