Abstract:The use of lime as a binder in hemp–lime considerably increases the drying time of hemp–lime after casting. Furthermore, lime is a non-renewable mineral resource. As such, this paper explores the effectiveness of using an alternative non-mineral binder instead of lime to formulate a novel hemp–shive insulation. The moisture-dependent thermal conductivity, adsorption isotherm, vapour diffusion resistance factor, and in-built hygrothermal performance of four variants of a novel bio-based insulation were investigated. The hygrothermal performance of the novel hemp–shive insulation was compared with that of a previously developed novel hemp–lime insulation. No significant variation in thermal conductivity of hemp–shive insulations between the equilibrium moisture contents (EMC) at 0% and 50% relative humidity (RH) was observed, but there was a substantial increase in thermal conductivity hemp–shive insulations when the material reached the EMC at 98% RH. The average dry thermal conductivity values of hemp–shive and hemp–lime insulations were also similar. The adsorption isotherms of hemp–shive insulations were determined at 0%, 20%, 50%, 70%, 90%, and 98% relative humidity steps. At 98% RH, the moisture adsorption capacity of hemp–shive insulations was 4-to-5-times higher than that of hemp–lime insulation. Hemp–shive insulations' vapour diffusion resistance factor (μ value) was about double the μ value of hemp–lime insulation. Hemp–shive insulations exhibited 4-to-5-times higher water absorption resistance than that of hemp–lime insulation. Numerically determined porosity values of hemp–shive agree with the values of wood-based insulation materials of similar density. Finally, using all experimentally acquired data as inputs, dynamic whole-building hygrothermal simulations were carried out and the results show that novel hemp–shive insulation materials perform at a similar level to the hemp–lime insulation in terms of heating and cooling energy demand but require 45% less energy for humidification. However, the relative humidity inside the hemp–shive wall remains higher than 70%, which can potentially induce mould growth.

Moisture buffer, fire resistance and insulation potential of novel bio-clay plaster

Experimental Investigation of Thermal Properties and Moisture Buffering Performance of Composite Interior Finishing Materials under Different Airflow Conditions

Enhancing fire safety and thermal performance: Wood composites with bio‐based phase change materials and fire retardants for building applications

Investigating the characteristics and thermal performance of plaster composites enhanced with paddy husk for sustainable Residential construction

Material properties of clay and lime plaster for structural fire design

Experimental performance assessment of a novel insulation plaster as an energy-efficient retrofit solution for external walls: A key building material towards low/zero carbon buildings

Research of the physical properties of bio-based building materials with phase change material

Assessing the Impact of Moisture Buffering Properties of materials on Indoor Environmental Quality: A Study on a Recycled Material Plaster

Performance Study of Lightweight Insulating Mortar Reinforced with Straw Fiber

Enhanced Resistance to Fire of the Bark-Based Panels Bonded with Clay

Paraffin/beeswax/plaster as thermal energy storage composite: Characterization and application in buildings

Development of Clay-Composite Plasters Integrating Industrial Waste

Development of a new lightweight gypsum composite: Effect of mixed treatment of barley straws with hot water and bio-based phase change material on the thermo-mechanical properties

Experimental Analysis of Moisture-Dependent Thermal Conductivity, and Hygric Properties of Novel Hemp–shive Insulations with Numerical Assessment of Their In-Built Hygrothermal and Energy Performance

Computational and experimental analysis of PCM-infused brick for sustainable heat regulation

Effect of multiphasic structure of binder particles on the mechanical properties of a gypsum-based material

Effect of moisture buffering on surface temperature variation: study of different indoor cladding materials

Study of a new capillary active bio-insulation material by hygrothermal simulation of multilayer wall

Experimental study of relative humidity absorbed through capillarity of building material under isothermal conditions: Clay-Kaolin reinforced with Alfa fibers

Thermal Performance of Lignocellulose's By-Product Wallboards with Bio-Based Microencapsulated Phase Change Materials

Hygro-thermo-mechanical properties of tunnel excavated earth-based plasters