Abstract:Abstract Mixed flow turbines offer additional design freedom compared with conventional radial turbines. This is useful in the automotive turbocharger application to reduce rotor inertia, which can be very beneficial for the transient response of a highly-boosted downsized passenger car powertrain. A previously published study from the authors analysed a series of nine mixed flow turbine rotors with varying blade cone angle and inlet blade angle. This paper reports an extension of that study with two further mixed flow turbine rotors where the chord length of the rotor blade was extended. The aim of this work was to understand both the aerodynamic and mechanical impacts of varying the chord length, particularly for the turbocharger application where off-design performance and transient response are very important. The baseline mixed flow rotor for this study had a blade cone angle of 30° and an inlet blade angle of 30°. Two further variations were produced; one with the TE extended in the downstream direction across the entire blade span. In the second variation the chord was extended at the hub corner only, while the shroud corner of the TE remained unchanged, with the aim of achieving some aerodynamic improvement while meeting mechanical requirements. When the blade was extended at both the hub and shroud, the inertia and stress levels increased significantly and the blade eigenfrequencies reduced. There was significant improvement in peak efficiency, but the mechanical performance was unfavourable. The improvement in peak efficiency was mainly due to better exhaust diffuser performance and therefore would not be realised in most turbocharger installations. The blade that was extended at only the hub corner incurred very little additional inertia, and the centrifugal stresses and blade eigenfrequencies were improved. Consequently, it was possible to reduce the blade thickness at the TE in order to achieve a more aerodynamically optimised design. In this case, the mechanical performance was acceptable and there were efficiency improvements of up to 1.1% pts at off-design conditions, with no reduction in peak efficiency or maximum mass flow rate. Therefore, the blade that was extended only at the hub produced some improvement within acceptable mechanical limits. The flow field features were considered for the three rotor geometries to explain the changes in loss and efficiency across the operating range.

Impact of blade number on performance, loss and flow characteristics of one mixed flow turbine

Statistical Investigations of Profile Error Impact on Flow and Performance of a Low-Pressure Turbine Cascade

Optimization Design of a Turbine Blade to Reduce Secondary Flow Loss Using a Viscous Adjoint Method

Computational aerodynamic performance of mixed-flow turbine blade design

Numerical and Experimental Investigation of the Impact of Mixed Flow Turbine Inlet Cone Angle and Inlet Blade Angle

Optimal Selection of Blade Number of Hydraulic Turbine Based on Computational Fluid Dynamics

Hydraulic Optimization and Loss Analyses of a Low Specific-Speed Centrifugal Pump with Variable-Thickness Blades

Influence of Blade-Flow Interactions on Flow Behaviours and Blade Loading of an Automotive Mixed-Flow Turbine

Design and Performance Analysis of Mixed Flow Turbine Rotors With Extended Blade Chord

Influence of runner blade number on hydraulic performance and flow control in draft tube of Francis turbine

Numerical Analysis on the Influence of the Twisted Blade on the Aerodynamic Performance of Turbine

Numerical Investigation of Lucid Spherical Cross-Axis Flow Turbine with Asymmetric Airfoil Sections and the Effect of Different Parameters of Blades on Its Performance

Investigation of blade design parameters for performance improvement of hydraulic cross flow turbine

Numerical investigation on bowed blades of large meridional expansion Turbine

CFD simulation and aerodynamic optimization of two-stage axial high-pressure turbine blades

Numerical Investigation on the Effect of Tip Clearance on a Turbine Stage Flow-field and Aerodynamic Performance

Loss Analysis of a Mix-Flow Turbine with Nozzled Twin-Entry Volute at Different Admissions

Computational investigation of the aerodynamics of automotive turbocharger mixed-flow turbines

NUMERICAL INVESTIGATION OF BLADE TIP LOSS EFFECT ON THE TORQUE OF H-ROTOR VERTICAL-AXIS WIND TURBINE

CFD and Taguchi based optimization of air driven single stage partial admission axial turbine blade profiles

Numerical Study on the Aerodynamic Performance of Three-stage Turbine Inner Flow Field with Cooling Air Mixing