Abstract:Optimization methods have been widely applied to the aerodynamic design of gas turbine blades. While applying optimization to high-fidelity computational fluid dynamics (CFD) simulations has proven capable of improving engineering design performance, a challenge has been overcoming the prolonged run-time due to the computationally expensive CFD runs. Reduced-order models and, more recently, machine learning methods have been increasingly used in gas turbine studies to predict performance metrics and operational characteristics, model turbulence, and optimize designs. The application of machine learning methods allows for utilizing existing knowledge and datasets from different sources, such as previous experiments, CFD, low-fidelity simulations, 1D or system-level studies. The present study investigates inserting a machine learning model that utilizes such data into a high-fidelity CFD driven optimization process, and hence effectively reduces the number of required evaluations of the CFD model. Artificial Neural Network (ANN) models were trained on data from over three thousand two-dimensional (2D) CFD analyses of turbine blade cross-sections. The trained ANN models were then used as surrogates in a nested optimization process alongside a full three-dimensional Navier–Stokes CFD simulation. The much lower evaluation cost of the ANN model allows for tens of thousands of design evaluations to guide the search of the best blade profiles to be used in the more expensive, high-fidelity CFD runs, improving the progress of the optimization while reducing the required computation time. It is estimated that the current workflow achieves a five-fold reduction in computational time in comparison to an optimization process that is based on three-dimensional (3D) CFD simulations alone. The methodology is demonstrated on the NASA/General Electric Energy Efficient Engine (E3) high pressure turbine blade and found Pareto front designs with improved blade efficiency and power over the baseline. Quantitative analysis of the optimization data reveals that some design parameters in the present study are more influential than others, such as the lean angle and tip scaling factor. Examining the optimized designs also provides insight into the physics, showing that the optimized designs have a lower amount of pressure drop near the trailing edge, but have an earlier onset of pressure drop on the suction side surface when compared to the baseline design, contributing to the observed improvements in efficiency and power.

CFD simulation and aerodynamic optimization of two-stage axial high-pressure turbine blades

Numerical Simulation and Aerodynamic Optimization of Two-Stage Axial High-Pressure Turbine Blades

Aerodynamic design of a high-efficiency two-stage axial turbine, using streamline curvature method and performance optimisation by clocking of stator blades

A Cfd Approach to Fluid Dynamic Optimum Design of Steam Turbine Stages with Stator and Rotor Blades

A cooled turbine blade design and optimization method considering the cooling structure influence

Aerodynamic and Heat Transfer Optimization of One Stage Air-Cooled Turbine

Optimization of the Blade Profile and Cooling Structure in A Gas Turbine Stage Considering Both the Aerodynamics and Heat Transfer

Optimization Design of Aspect Ratio and Solidity of a Heavy-Duty Gas Turbine Transonic Compressor Rotor

Three-Dimensional Optimization of Blade Lean and Sweep for an Axial Compressor to Improve the Engine Performance

Fluid Dynamic Efficiency Optimization of Steam Turbine Stages Considering Leakage Influences and Inter-stage Reciprocal Interferences

CFD and Taguchi based optimization of air driven single stage partial admission axial turbine blade profiles

Three Dimensional Optimum Design Of A Steam Turbine Stage With Nurbs Curves

Optimization of Turbine Blade Aerodynamic Designs Using CFD and Neural Network Models

Steam turbine high-pressure reaction stages; new 3D vortices breakdown and airfoil optimization method

Study on Aerodynamic Optimization Design Process of Multistage Axial Turbine

Aeromechanical optimization of first row compressor test stand blades using a hybrid machine learning model of genetic algorithm, artificial neural networks and design of experiments

A Dimension Reduction-Based Multidisciplinary Design Optimization Method for High Pressure Turbine Blades

Integrated optimization method for transonic turbine based on direct free-form deformation and prescreening differential evolutionary optimizer

Efficient aerodynamic optimization of turbine blade profiles: an integrated approach with novel HDSPSO algorithm

NUMERICAL STUDY ON THE FLOW FIELD ANALYSIS AND OPTIMIZATION OF TURBINE IN SUPERCRITICAL COMPRESSED AIR ENERGY STORAGE

Multi-objective optimization of aerodynamic and erosion resistance performances of a high-pressure turbine