Abstract:Modern gas turbine endwall is operating in harsher conditions for the application of low NOx combustor. Non-axisymmetric endwall has been extensively studied for aerodynamic performance improvement, because endwall contouring can decrease the pressure gradient between the pressure side (PS) and the suction side (SS) in the blade passage. In addition to the influence of pressure gradient on aerodynamic losses, the vortical structures induced by pressure gradient are also the sources of high heat transfer regions in the passage. Consequently, thermal loads might be reduced by decreasing the pressure gradient thus weakening the strength of the secondary flows. In terms of engineering applications, distribution of thermal load is very important for the design of endwall cooling scheme, and it is necessary to take both aerodynamic and heat transfer performances into consideration for the endwall profile design. In this work, aero-thermal coupled design optimization of a turbine blade endwall was carried out. The endwall contour was obtained by multiplying heights of two curves in the streamwise and pitchwise directions. The streamwise curve was controlled by non-uniform B-spline (NUBS) and the pitchwise one was obtained by employing the sinusoidal function. The optimization method adopted in this research was the multi-objective genetic algorithm (MOGA) coupled with Kriging (KRG) model, which has been validated by benchmark functions. Numerical validation shows that static pressure coefficients on the blade surfaces and the Nusselt number (Nu) on the endwall agree well with the experimental results. The design variables were the endwall profile parameters, and the objective functions were maximizing total pressure recovery coefficient (ξ) at the blade outlet and minimizing the Nu on the endwall. Two optimal cases were selected from the Pareto front and analyzed in detail. It is indicated that the turbine blade aerodynamic performance can be improved while the heat transfer is restrained simultaneously. For the optimal Case I, mass flow-averaged ξ increases by 0.88%, and for Case II, area-averaged Nu reduces by about 7.78%.

Secondary Flow Reduction By Blade Redesign And Endwall Contouring Using An Adjoint Optimization Method

Optimization Design of a Turbine Blade to Reduce Secondary Flow Loss Using a Viscous Adjoint Method

Optimization of Endwall Contours of a Turbine Blade Row Using an Adjoint Method

Turbine Blade Row Optimization Through Endwall Contouring by an Adjoint Method

Three-Dimensional Aerodynamic Design Optimization of A Turbine Blade by Using an Adjoint Method

Multipoint Design Optimization of a Transonic Compressor Blade by Using an Adjoint Method

Multi-Objective Design Optimization of a Transonic Compressor Rotor Using an Adjoint Equation Method

Adjoint Aerodynamic Optimization of a Transonic Fan Rotor Blade with a Localized Two-Level Mesh Deformation Method

Aerodynamic Shape Optimization of a Transonic Fan by an Adjoint-Response Surface Method

Adjoint-Response Surface Method in Aerodynamic Shape Optimization of Turbomachinery Blades

Aerodynamic Shape Optimization Of A Turbine Blade Considering Geometric Uncertainty Using An Adjoint Method

Flow Reconstructions and Aerodynamic Shape Optimization of Turbomachinery Blades by POD-based Hybrid Models

A Gradient-Based Method Assisted by Surrogate Model for Robust Optimization of Turbomachinery Blades

Aerodynamic Loss for a Turbine Blade With Endwall Leakage Features and Contouring

Investigation of non-axisymmetric endwall contouring in a high loaded turbine stator cascade

Multi-Stage Turbomachinery Blades Optimization Design Using Adjoint Method And Thin Shear-Layer N-S Equations

Aero-Thermal Coupled Design Optimization of the Non-Axisymmetric Endwall for a Gas Turbine Blade

Hybrid RANS/LES Study of Complex Turbulence Characteristics and Flow Mechanisms on the Highly-Loaded Turbine Endwall

Control mechanism of secondary flow in a turbine cascade with non-axisymmetric endwall profiling under Co-rotating incoming vortex

Blade Design with Three-Dimensional Viscous Analysis and Hybrid Optimization Approach

A Dimension Reduction-Based Multidisciplinary Design Optimization Method for High Pressure Turbine Blades