Abstract:In aeroengines, purge flow directly fed from the compressor (which bypasses the combustor) is introduced through the disk space between blade rows to prevent the hot ingress. Higher quantity of purge gas fed through the wheel space can provide additional thermal protection to the passage endwall and blade surfaces. However, the interaction of purge flow with the mainstream flow leads to higher secondary losses. Secondary losses inside a turbine blade passage can be reduced effectively by endwall contouring. This paper presents computational investigation on the influence of non-axisymmetric endwall contouring over endwall secondary flow modification in the presence of purge flow with the pressure side bubble (PSB). The experimental analysis was conducted for the base case without purge and base case with purge (BCP) configurations having flat endwalls. The total pressure loss coefficient and exit yaw angle deviation were measured with the help of a five-hole pressure probe. Static pressure distribution over the blade midspan was obtained by 16 channel Scanivalve. Aerodynamic performances of three different profiled endwalls are numerically analyzed and are compared against the BCP configuration. The effects of different contoured endwall geometries on endwall static pressure distribution and secondary kinetic energy were also discussed. Analysis shows that in the first contoured endwall configuration (EC1), the formation of stagnation zones at a contour valley close to the suction surface causes the exit total pressure loss coefficient to increase. The shifting of the contour valley near to the pressure surface (EC2 configuration) has resulted in local acceleration of the diverted pressure side leg of the horseshoe vortex over the hump toward the end of the passage. In the third configuration (EC3 configuration), reduced valley depth and optimum hump height have effectively redistributed the endwall pitchwise pressure gradient. The increased static pressure coefficient at the endwall near to the pressure surface has eliminated the PSB formation. In addition, computational results of unsteady Reynolds averaged Navier–Stokes simulations are obtained for analyzing transient behavior of PSB, with more emphasis on its migration on the pressure surface and transport across the blade passage. The additional work done by the mainstream fluid to transport the low momentum PSB fluid has caused higher aerodynamic penalty at the blade exit region. In this viewpoint, the implementation of contoured endwalls has shown beneficial effects by eliminating the PSB and related secondary vortices. At 27% of axial chord downstream of the blade trailing edge, a 4.1% reduction in the total pressure loss coefficient was achieved with endwall contouring.

Aerodynamic Loss for a Turbine Blade With Endwall Leakage Features and Contouring

Secondary Flow Reduction By Blade Redesign And Endwall Contouring Using An Adjoint Optimization Method

Optimization Design of a Turbine Blade to Reduce Secondary Flow Loss Using a Viscous Adjoint Method

Optimization of Endwall Contours of a Turbine Blade Row Using an Adjoint Method

Turbine Blade Row Optimization Through Endwall Contouring by an Adjoint Method

Aerodynamic performance of profiled endwalls with upstream slot purge flow in a linear turbine cascade having pressure side separation

The Aerodynamic Optimization Design of Turbine Cascade Nonaxisymmetric Endwall and the Midgap Influence Assessment

Investigation of non-axisymmetric endwall contouring in a high loaded turbine stator cascade

Numerical Investigation of a Turbine Stator with Nonaxisymmetric Endwall Profiling

Endwall Contouring for Improving Aerodynamic Performance in a High-Pressure Turbine Cascade

Improving the Aerodynamic Performance of a High-Loading Turbine Blade by End-Wall Surface Structures

The Aerodynamic Optimization Design Of Turbine Cascade With Nonaxisymmetric Endwall And Experimental Validations

Large Eddy Simulation and RANS Analysis of the End-Wall Flow in a Linear Low-Pressure-Turbine Cascade—Part II: Loss Generation

Non-Axisymmetric Endwall Contouring in a Linear Compressor Cascade

Unsteady Flows of a Highly Loaded Turbine Blade with Flat Endwall and Contoured Endwall

The Nonaxismmetric Endwall Aerodynamic Optimization Design for a Large Turbine Cascade with a Midgap

Non-Axisymmetric Turbine Endwall Aerodynamic Optimization Design Part I: Turbine Cascade Design and Experimental Validations

Contoured Endwall Flow And Heat Transfer Experiments With Combustor Coolant And Gap Leakage Flows For A Turbine Nozzle Guide Vane

Application and Development of the Non-Axisymmetrical Endwall Contouring in the Turbomachinery

Influence of Endwall 2D Contouring on Endwall Adiabatic Cooling Effectiveness and Aerodynamic Performance

Enhancing Aerodynamic Performance of a Non-Axisymmetric Endwall Contoured Cascade Through Section Profiling Method