Abstract:To obtain a high-strength medium-thick AlCu dissimilar joint, a novel splat cooling assisted double side friction stir welding (SDS-FSW) is proposed. The microstructure and tensile properties of conventional double-side friction stir welding (DS-FSW) and the novel SDS-FSW joints under optimal welding parameters are systematically compared, it shows that the utilization of in-process splat cooling significantly reduces the welding peak temperature and the high-temperature dwell time. The in-process splat cooling causes significant grain refinement in the welding nugget zone (WNZ) of the AlCu dissimilar SDS-FSWed joint, it exists the lower recrystallization fraction and the higher KAM value. Although both DS-FSW and SDS-FSW joints fracture at the AlCu interface, the DS-FSW joint represents a brittle fracture characteristic, while the SDS-FSW joint represents a mixed ductile-brittle fracture mode. Under the drive of the mechanical stirring of the tool and the welding thermal cycle, the aluminium atoms and copper atoms diffuse to the copper base material and aluminium base material, respectively. Since copper diffuses in aluminium at a higher diffusion rate than aluminium diffuses in copper, and the solubility of copper in aluminium is much smaller than that of aluminium in copper, thus the Al 2 Cu becomes the first phase with the nucleation and growth. As the welding temperature and time continue to increase, Al 2 Cu reaches the supersaturation state, and the Al 4 Cu 9 phase is produced between the Cu (Al) and the Al 2 Cu phase. In the end, the interface forms the stable double-layer IMCs structure (Al 2 Cu/Al 4 Cu 9 ). The optimal tensile strength of the SDS-FSWed joint is 159 MPa, which is increased by 42% compared to the DS-FSWed joint at the same welding parameter. This was mainly because in-process splat cooling contributed to forming a thinner IMCs layer at the AlCu interface. It reveals that the application of in-process splat cooling is a versatile method to thin the IMCs layer at the Al/Cu medium-thick DS-FSW process.

Metallurgical and Mechanical Properties of Al–Cu Joint by Friction Stir Spot Welding and Modified Friction Stir Clinching

Microstructure, Corrosion and Mechanical Properties of Medium-Thick 6061-T6 Alloy/T2 Pure Cu Dissimilar Joints Produced by Double Side Friction Stir Z Shape Lap-Butt Welding

Microstructural characterization and mechanical properties of micro friction stir welded dissimilar Al/Cu ultra-thin sheets

Microstructure and Mechanical Properties Analysis of Al/Cu Dissimilar Alloys Joining by Using Conventional and Bobbin Tool Friction Stir Welding

Microstructure and Mechanical Properties of Dissimilar Double-Side Friction Stir Welds Between Medium-Thick 6061-T6 Aluminum and Pure Copper Plates

Intermetallic Compounds Formation in Dissimilar Friction Stir Welding of Mg/Cu Alloys

Effect of Dispersing In Situ Al-Cu Intermetallic Compounds on Joint Strength in Friction Stir Welding of AA3003-H18 Sheets

Microstructural Characterisation and Mechanical Properties of Dissimilar AA5083-copper Joints Produced by Friction Stir Welding

Improving bonding strength of medium-thick Al-Cu dissimilar joint by a novel splat cooling assisted double side friction stir welding

Experimental Investigation and Characterization of Friction Stir Spot-Welded Dissimilar Aluminum Copper Metallic Lap Joints

Stationary shoulder friction stir welding of Al–Cu dissimilar materials and its mechanism for improving the microstructures and mechanical properties of joint

Effect of Solid Solution Phase Constitution on Dissimilar Al/Cu FSW Using Zn As an Alloying Element at the Joint Interface

Improving the microstructure and mechanical properties of Al-Cu dissimilar joints by ultrasonic dynamic-stationary shoulder friction stir welding

Effect of Tool-Workpiece Relative Position on Microstructure and Mechanical Properties of Al-Cu Dissimilar Friction Stir Weld

Effect of Zn-brazed-interface on Microstructures and Mechanical Properties of Dissimilar 2A12/AZ31 Alloys Friction Stir Lap Welds

Conventional and swing friction stir spot welding of aluminum alloy to magnesium alloy

Microstructure and Mechanical Properties of Friction Stir-Welded Dissimilar Joints of ZK60 and Mg-4.6Al-1.2Sn-0.7Zn Alloys

Mechanical Behavior and Microstructure of Ultrasonic-Spot-Welded Al/Cu Dissimilar Joints with Zn Interlayer

Mechanical Properties of the AlCu4Mg1 Alloy Joint Manufactured by Underwater Friction Stir Welding

Microstructure and Mechanical Behavior of Friction Stir-Welded Sc-Modified Al-Zn-Mg Alloys Made Using Different Base Metal Tempers

Effect of Stirring Pin on Interfacial Microstructure and Mechanical Properties of FSSW-B Joint