Abstract:In friction stir welding, geometrical and motion features of the tool or pin greatly influence the interaction between the tool and workpiece as well as the resulting joint microstructure and mechanical properties. In order to enhance the material flow by optimizing the tool geometrical features, a new strategy was proposed in this study to introduce eccentric motion by offsetting the pin from the tool shoulder, and thin Al–Mg-Si aluminum alloy plates were friction stir welded by varying the pin eccentricity. The material flow and mixing characteristic were analyzed by optical microscope and tracer material method. The grain size and micro-texture of the stir zone were analyzed by electron backscatter diffraction. Uniaxial tensile tests and digital image correlation were conducted to evaluate the mechanical properties and observe the in situ strain evolution. The results show that pin eccentricity has a positive effect on promoting the material flow and grain refinement in the stir zone. The texture intensity was increased as pin eccentricity was introduced, and the dominant texture component converted from C {001} (without eccentricity) to / {112} when eccentric pin was used. However, no discerning change can be seen in the thermal history between samples. Despite the variation in softening of the stir zone with eccentricity, the ultimate tensile strength change was negligible. The average ultimate tensile strength reached approximately 198 MPa regardless of the pin eccentricity, and all joints fractured at the heat-affected zone. However, the softened stir zone caused by pin eccentricity resulted in an obvious increase in the joint elongation. It can be concluded that pin eccentricity significantly improved the material flow and grain refinement in the stir zone as well as enhanced the toughness of the weld joint.

Effect of Stirring Pin on Interfacial Microstructure and Mechanical Properties of FSSW-B Joint

The effect of pin diameter, tool penetration depth and plate arrangement on mechanical and metallurgical properties of 6061-T6 and 5052-T32 aluminum dissimilar joints in friction stir spot welding (FSSW)

Study on the Microstructure and Mechanical Properties on Al/Carbon Fiber Reinforced Thermoplastic Dissimilar Friction Stir Lap Welding Joints

Investigation of tool offset on the microstructure and mechanical properties of AA6061-T6/PC Friction Stir Butt Welding joint

Effect of Stirring Pin Rotation Speed on Microstructure and Mechanical Properties of 2A14-T4 Alloy T-Joints Produced by Stationary Shoulder Friction Stir Welding

The role of pin eccentricity in friction stir welding of Al-Mg-Si alloy sheets: microstructural evolution and mechanical properties

Depriving friction stir weld defects in dissimilar aluminum lap joints

Effect of Zn-brazed-interface on Microstructures and Mechanical Properties of Dissimilar 2A12/AZ31 Alloys Friction Stir Lap Welds

Effect of Tool Pin Profile on Mechanical and Metallurgical Properties of the Friction Stir Welded Joint of AA6061 and AZ91D

Microstructure and Mechanical Properties of Mg-Li/Al Dissimilar Joints via Dynamic Support Friction Stir Lap Welding

Microstructure and Mechanical Properties of Static Shoulder Friction Stir Welding AA3003-H14

Parametric effect on microstructure evolution, grain size and mechanical behaviour of friction stir butt welding of AA6061-T6 alloy

Microstructure evolution and mechanical properties of friction stir welded joint of ultrafine-grained dissimilar AA2024/AA5083 composite fabricated by accumulative roll bonding

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Influence mechanism of pin thread in friction stir welding of magnesium alloys based on the relationship between microstructure and mechanical properties

Combined effect of nanocompositing and addition of interlayer on friction stir welding of aluminum/magnesium joint: a study

Stationary shoulder friction stir welding of Al–Cu dissimilar materials and its mechanism for improving the microstructures and mechanical properties of joint

Effect of Tool Speed on Microstructure Evolution and Mechanical Properties of Friction Stir Welded Joints of Al-Mg-Si Alloy with High Cu Content

Metallurgical and Mechanical Properties of Al–Cu Joint by Friction Stir Spot Welding and Modified Friction Stir Clinching

Friction stir lap welding for dissimilar materials of aluminum alloy and carbon-fiber-reinforced polyetherimide

Influence of Welding Combined Plastic Forming on Microstructure Stability and Mechanical Properties of Friction Stir-Welded Al-Cu Alloy