An optimal separation method for high-precision K isotope analysis by using MC-ICP-MS with a dummy bucket

Xiaoqiang Li,Guilin Han,Qian Zhang,Zhuang Miao

DOI: https://doi.org/10.1039/d0ja00127a

2020-01-01

Journal of Analytical Atomic Spectrometry

Abstract:High-precision potassium isotope analysis by MC-ICP-MS: a novel chromatographic method (single column) and cross-disciplinary research.

spectroscopy,chemistry, analytical

What problem does this paper attempt to address?

High-precision Analysis of Potassium Isotopes by MC-ICP-MS Without Collision Cell Using Cool Plasma Technique in Low-Resolution Mode

Hai-Ou Gu,He Sun

DOI: https://doi.org/10.1039/d1ja00201e

2021-01-01

Journal of Analytical Atomic Spectrometry

Abstract:A practical method to measure K isotopes with MC-ICP-MS without a collision cell in low-resolution mode.
High-precision Determination of Stable Potassium and Magnesium Isotopes Utilizing Single Column Separation and Multicollector Inductively Coupled Plasma Mass Spectrometry

Chao Huang,Hai-Ou Gu,He Sun,Fangyue Wang,Bin Chen

DOI: https://doi.org/10.1016/j.sab.2021.106232

2021-01-01

Abstract:With advances in analytical precision by multicollector inductively coupled plasma mass spectrometry, K and Mg isotopes are increasingly used as a combined tool in tracing sources and processes in geoscientific research. However, reported methods in the literature require at least two column separation procedures during sample purification, which is time-consuming (at least two days). Therefore, a single column procedure could improve efficiencies, and these efforts are necessary to extend the combined application of K and Mg isotopes as geological tracers. In this study, a simple and time-efficient chromatographic procedure was reported, utilizing a single column for quantitative separation of both K and Mg from sample matrices for high-precision isotopic measurement of K and Mg. Using this novel method, the results for international geological standards agreed with published values, verifying the robustness of the procedure. The popularization of this optimized procedure would potentially extend the combined application of K and Mg isotopes in geological studies.
High precision potassium isotope analysis of geological samples using MC-ICP-MS

CHEN Yaqi,SUN He,GU Haiou,HUANG Chao,CAO Ziyi,WANG Fangyue,GE Can

DOI: https://doi.org/10.19762/j.cnki.dizhixuebao.2022032

2023-01-01

Acta Geologica Sinica

Abstract:In recent years, with the rapid development of multi-collector inductively coupled plasma-mass spectrometry（MC-ICP-MS）, the analytical precision of potassium（K） isotopes has been greatly improved, which in turn has promoted their development as potential geochemical tracers in processes involving continental weathering, crust-mantle interaction, and so on. Until now, the cumbersome and time-consuming process of sample pretreatments and the poor analytical accuracy caused by argon hydrides interference are still the biggest obstacles to the wide application of K isotopes. After completely dissolving the samples with hydrochloric acid, nitric acid, and hydrofluoric acid, purification of K from major matrix was performed on a customized quartz ion exchange column packed with ～2.7 mL of AG50W-X8 cation exchange resin（BioRad TM,200～400 mesh） using 0.5 mol/L HNO 3 as the eluent. This one-step procedure can effectively separate K from Li, Na, Ti, Mg, Mn, Al and Ca, except for Cr, in most of the geological samples. To find the appropriate method for high-precision stable K isotopic measurements, for minimizing the ArH + yield and improving the stability of the instrument, three methods were compared here（the high-resolution mode, high-resolution mode with continuous acquisition measurement run mode, and the low-resolution mode with a method designed to eliminate ArH + interference）. The low-resolution mode has the advantages of low cost, high stability, and high precision（long-term precision at about 0.08‰ for our laboratory）. When used to measure the K isotopic composition of a series of international geological reference materials, the results are consistent with previous values within analytical precision, indicating the reliability of this method. The K isotopic composition of a set of Chinese national rock standard materials is determined here. The measured values of K isotopes can provide a reference for the data comparison between different laboratories in future.
Precise measurement of stable potassium isotope ratios using a single focusing collision cell multi-collector ICP-MS

Weiqiang Li,Brian L. Beard,Shilei Li

DOI: https://doi.org/10.1039/C5JA00487J

2016-01-01

Journal of Analytical Atomic Spectrometry

Abstract:High precision potassium isotope ratio measurements were made using a collision-cell equipped single focusing Multi-Collector Inductively Coupled Plasma Mass Spectrometer (MC-ICP-MS). Interferences on 41K from 40ArH+ were largely suppressed through collision with He gas atoms, and reaction with H2 or D2 gas molecules in the collision cell under optimum collision gas flow conditions. Using H2 or D2 as the collision gas, we distinguish charged argon–deuterium molecules (ArD+) generated in the collision cell from argon hydride (ArH+) generated in the plasma or in the interface region (referred to as “plasma-related AH+” hereafter), and demonstrate, for the first time, that both plasma-related and collision cell-generated ArH+ are important sources of ArH+ that interfere with 41K+ in collision-cell ICP-MS instruments that use H2 as a collision gas. The use of D2 instead of H2 as a reactive gas in the collision cell resulted in better overall performance in K isotope ratio measurements. By combining these mass spectrometry methods with chemical purification of K by ion exchange chromatography, we achieved an internal precision of u003c±0.07‰ (2 standard error) and an external reproducibility of u003c±0.21‰ (2 standard deviation, or 95% confidence) in the 41K/39K ratio measurement for geological and biological samples. With the improved precision, it is possible to distinguish a ∼1.3‰ variation in K isotope compositions (41K/39K ratios) among seawater, igneous rocks, and biological samples. The K isotope system is likely to be beneficial in providing a better understanding of potassium cycling during continental weathering and the uptake of nutrients by plants.
Optimization of analytical conditions for precise and accurate isotope analyses of Li, Mg, Fe, Cu, and Zn by MC-ICPMS

Yan Hu,Fang-Zhen Teng

DOI: https://doi.org/10.1039/c8ja00335a

2019-01-01

Journal of Analytical Atomic Spectrometry

Abstract:Analytical advances in Multi-Collector Inductively Coupled Plasma Mass Spectrometry (MC-ICPMS) over the past decade have led to rapid growth in studies utilizing non-traditional stable isotopes. There are substantial analytical challenges for achieving precise and accurate measurements of these isotopes that limit their applications in geoscience where natural isotopic variations are generally small. Here, we evaluate experimental factors that may affect the accuracy and repeatability of isotopic measurements of selected stable metal isotopes (Li, Mg, Fe, Cu, and Zn) on a Nu Plasma II MC-ICPMS to provide optimized analytical protocols for acquiring high quality data. Our results suggest that the repeatability level (2SD) that is readily obtainable for delta Li-7 is +/- 0.09 parts per thousand to +/- 0.24 parts per thousand, for delta Mg-26 is +/- 0.03 parts per thousand to +/- 0.07 parts per thousand, for delta Fe-56 is +/- 0.05 parts per thousand to +/- 0.07 parts per thousand, for delta Cu-65 is +/- 0.03 parts per thousand to +/- 0.05 parts per thousand, and for delta Zn-66 is +/- 0.02 parts per thousand to +/- 0.04 parts per thousand. Instrumental mass bias for these isotope systems can be corrected adequately using the standard-sample bracketing method but it requires that target elements are of high purity, a close match in analyte concentrations between samples and bracketing standards, and preparation of all running solutions using the same concentration of nitric acid. Overall, the Nu Plasma II is well suited for precise and accurate analyses of the isotopes studied here, and the optimal results were obtained using a 'wet' plasma operating at a normal radio-frequency (RF) power.
An Efficient Li Dual-Column System and High-Precision Li Isotope Measurement of High Matrix and Low-Li Samples by MC-ICP-MS

Cheng Cao,Tao Li,Tianyu Chen,Gaojun Li,Wei Li,Jun Chen

DOI: https://doi.org/10.1039/d3ja00054k

2023-01-01

Journal of Analytical Atomic Spectrometry

Abstract:Over the last decade, there has been a growing interest in using lithium (Li) isotopes in marine carbonates to trace chemical weathering and clay formation in the Earth's history. Yet it remains technically challenging to precisely and efficiently determine the Li isotope composition in carbonate samples due to the imperfect Li separation led by the matrix effect and the extremely low Li concentration in carbonates relative to the analytical threshold of sample size. For such high matrix and low-Li samples, here we present an efficient dual-column chromatography system for Li purification. The dual-column system has a large loading capacity, fixed Li elution range of merely 12 mL, complete Li recovery (>99.5%) and relatively efficient total elution time (7 hours). The procedural blank is 0.036 & PLUSMN; 0.002 ng accounting for sample dissolution and chemical purification, and the Na/Li mass ratio of the Li cut is below 0.5. High precision and accurate Li isotope measurement is performed efficiently with a small sample-sized protocol developed on a MC-ICP-MS (Neptune plus) connected with an APEX 2-IR desolvator. The whole procedure is validated by analyzing a series of certified reference materials. The long-term external precision of & delta;Li-7 determined based on L-SVEC and a high-purity Li solution is 0.6 & PTSTHOUSND; (2SD) and 0.9 & PTSTHOUSND; (2SD) for a minimum sample size of 7.5 ng.
Low-Consumption and High-Efficiency Isotope Analysis by Microultrasonic Single-Droplet Nebulization Sampling Multicollector Inductively Coupled Plasma Mass Spectrometry

Junhang Dong,Yang Yu,Zhujun Dai,Shuyang Li,Linjie Chen,Pengju Xing,Guan Wang,Xing Liu,Hongtao Zheng,Zhenli Zhu

DOI: https://doi.org/10.1021/acs.analchem.4c04312

IF: 7.4

2024-12-01

Analytical Chemistry

Abstract:Metal stable isotopes are increasingly applied in various fields, including planetary science and medical research, highlighting the need for isotope analysis methods capable of handling precious and microvolume samples. This study introduces a novel, low-consumption, high-efficiency isotope analysis method using MC-ICP-MS based on microultrasonic single-droplet nebulization (MUSDN). The proposed MUSDN enables the complete nebulization of microliter-sized droplets, delivering high-sensitivity...

chemistry, analytical
Isotope Separation of Potassium with a magneto-optical combined method

Zixuan Zeng,Shangjin Li,Bo Yan

DOI: https://doi.org/10.48550/arXiv.2111.10918

2021-11-21

Atomic Physics

Abstract:Due to the similar physical and chemical properties, isotopes are usually hard to separate. On the other hand, the isotope shifts are very well separated in a high-resolution spectrum, making them possible to be addressed individually by lasers, thus separated. Here we report such an isotope separation experiment with Potassium atoms. The isotopes are independently optical pumped to the desired spin states, and then separated with a Stern-Gerlach scheme. A micro-capillary oven is used to collimate the atomic beam, and a Halbach-type magnet array is used to deflect the desired atoms. Finally, the $^{40}$K is enriched by two orders of magnitude. This magneto-optical combined method provides an effective way to separate isotopes and can be extended to other elements if the relevant optical pumping scheme is feasible.
High precision analysis of potassium stable isotopes using the collision/reaction cell Neoma MC-ICPMS/MS

Nicole Nie,Rosa Grigoryan,François L.H. Tissot

DOI: https://doi.org/10.1039/d4ja00133h

2024-06-20

Journal of Analytical Atomic Spectrometry

Abstract:Potassium isotopes hold great promise for tracing geological processes, but their analyses are fraught with complexities. Various methods using different generations of MC-ICPMS instruments have been developed, each with distinct advantages and disadvantages. In this study, we report on K isotopic measurements performed using the Thermo Scientific Neoma collision cell MC-ICPMS/MS to explore the potential of the instrument. The tests were conducted under wet plasma conditions, and the precision achieved was ~0.03 to 0.1 ‰ (95% c.i.) for 5–25 measurements in a single analytical session, comparable to other established techniques. The measurements were accurate within the tested concentration range of 50–500 ppb K. A K concentration mismatch between samples and standards of up to 5% was acceptable, while acid molarity mismatch had a pronounced effect on the measured K isotopic compositions. Matrix elements did not significantly impact K isotopic measurements when their concentration was below 2% of K. Several geostandards were measured, and the obtained values agree with those from other measurement techniques. Overall, our tests suggest that measuring K isotopes with Neoma collision cell MC-ICPMS/MS is possible, but the high sensitivity of the instrument to tuning settings requires considerable efforts for conducting such measurements.

spectroscopy,chemistry, analytical
Precise magnesium isotope analyses of high-K and low-Mg rocks by MC-ICP-MS

Zhian Bao,Kangjun Huang,Tianzheng Huang,Bing Shen,Chunlei Zong,Kaiyun Chen,Honglin Yuan

DOI: https://doi.org/10.1039/c9ja00002j

2019-01-01

Journal of Analytical Atomic Spectrometry

Abstract:This study presents a chemical protocol for the separation of Mg that is particularly adapted for diverse igneous rock samples, especially for high-K and low-Mg rocks. This protocol is based on a combination of three procedures: the removal of K from the samples using the precipitation procedure, followed by the separation of Fe and Ca using 2 mL of AG50W-X12 cation exchange resin, and finally the removal of Al, Ti, Na, and Fe elements using 0.5 mL of AG50W-X12 cation exchange resin. The effect of acidity and concentration mismatch as well as the matrix effect were rigorously evaluated using Nu Plasma II MCI-CP-MS with a wet plasma mode. The delta Mg-26 mean values of the GSB and Alfa Mg standard solutions are -2.05 +/- 0.05 parts per thousand (2 standard deviation (2s), n = 106) and -3.91 +/- 0.04 parts per thousand (2s, n = 51), respectively, which serve as in-house Mg standards in the State Key Laboratory of Continental Dynamics (SKLCD). The average delta Mg-26 value of one multi-elemental Mg standard GSB-1, made by adopting GSB with matrix elements, agrees well with the recommended value after precipitation and chromatographic separation. The long-term reproducibility, assessed by repeated measurements of Mg standard solutions and reference materials (RMs), is +/- 0.06 parts per thousand. The robustness of our method is further assessed by the replicated analyses of fifteen rock standards and olivine grains with large variations in MgO and K2O content.
A single-column and efficient procedure for separating Fe and Mg from geological materials for isotopic analyses using MC-ICP-MS

Guanhong Zhu,Zhenmin Ge,Le Zhang,Gangjian Wei,Jinlong Ma

DOI: https://doi.org/10.1039/d4ja00272e

2024-10-05

Journal of Analytical Atomic Spectrometry

Abstract:Fe and Mg isotopes have increasingly served as combined proxies for geological processes. Fe and Mg isotope determination requires consuming different splits of samples and multi-column chromatographic purification to obtain pure Mg and Fe fractions in conventional chemical procedures, which is time-consuming and not suitable for rare and valuable samples. This study presents a novel and efficient chromatographic procedure to purify both Fe and Mg from geological matrices, using a single-column loaded with AGMP-50 resin, followed by precise measurements of Fe and Mg isotopes by multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS). In our experiment, the Fe fraction was first collected by 7 mL of a mixture of 0.2 M HCl and 0.5 M HF, and then the Mg fraction was collected using 9 mL of 1.3 M HCl. This procedure is suitable for processing different types of rock samples and enabling a Fe recovery of >98% and a full recovery for Mg, with effective removal of matrix elements such as Al, Ti, Na, K, Ca, and other trace elements. Using this method, Fe and Mg isotopic compositions of various geological reference materials were reported. All of the Fe and Mg isotopic analytical results were in agreement with the reported data within analytical uncertainties, verifying that the method established here is robust and reproducible. Thus, this procedure will serve as a great option for obtaining both Fe and Mg isotopic compositions of geological samples and tracing geochemical or astrochemical processes in the future.

spectroscopy,chemistry, analytical
Author Response for "application of a “continuous‐acquisition‐method” to Potassium Isotope Measurement by Multi‐collector Inductively Coupled Plasma Mass Spectrometry"

Hai-Ou Gu,He Sun,Chao Huang,Fangyue Wang,Can Ge

DOI: https://doi.org/10.1002/rcm.9105

2021-01-01

Abstract:RationaleThe very small mass difference between 41K and 40ArH+ makes the flat, hydride interference‐free peak shoulders very narrow (0.002–0.003 m/z unit), bringing a number of analytical challenges when measuring K isotopic compositions by multi‐collector inductively coupled plasma mass spectrometry (MC‐ICP‐MS). In traditional Sequence Run mode, the parameters are loaded every line of the sequence which can introduce tiny drifts of tune parameters and mass peaks. This may occasionally lead to the failure of K isotope measurements when mass drifts exceed 0.002 m/z unit. It is thus essential to keep the tune parameters, especially the magnet current, very stable to achieve high‐precision K isotopic compositions.MethodWe developed a “Continuous‐Acquisition‐Method” (CAM) MC‐ICP‐MS Run mode to improve the stability when determining K isotopes. Two sets of experiments were designed: (a) Stability test: measuring a single pure K solution (viz. NIST‐999c) for ~3 h and comparing the stability of the two run modes; and (b) GSB‐K test: measuring our inhouse pure K standard solution (GSB‐K) in both run modes and comparing the accuracy and precision.ResultsThe traditional Sequence Run mode only kept the MC‐ICP‐MS system stable for the first ~1.5 h during the ~3‐h test, with an offset of the mass peaks of ~0.003 m/z unit. The CAM Run mode yielded higher stability during the whole test (~3 h), with a peak shift <0.0004 m/z unit. Measurement of the GSB‐K standard solution in Sequence Run and CAM Run modes gives identical δ41K values when the magnet was kept stable, with the CAM Run mode offering a better precision and keeping the instrument stable for longer time.ConclusionsThe MC‐ICP‐MS CAM Run mode shows higher stability and better precision. It is, therefore, good for high‐precision K isotope measurements.
Precise Measurement of 41 K/ 39 K Ratios by High-Resolution Multicollector Inductively Coupled Plasma Mass Spectrometry under a Dry and Hot Plasma Setting

Shichao An,Xianglong Luo,Weiqiang Li

DOI: https://doi.org/10.1002/rcm.9289

IF: 2.586

2022-01-01

Rapid Communications in Mass Spectrometry

Abstract:Rationale Stable K isotope geochemistry is becoming an important tool for various applications. Developments in analytical methods for K isotopes based on multicollector inductively coupled plasma mass spectrometry (MC-ICP-MS) without collision cell will bring research capability of K isotopes to many existing MC-ICP-MS labs. Methods Stable K isotopes were analyzed without applications of "cold plasma" and collision cell on a Nu 1700 Sapphire high-resolution multicollector inductively coupled plasma mass spectrometer. A conventional dry and hot plasma setting is used for analysis to maintain high K sensitivity and signal stability, and high mass resolution was applied to provide interference-free shoulders of K-39(+) for isotopic measurement of K-41/K-39 ratios. Ar-40(+) ion beam generated in ICP was neutralized in the ion guide rail for the Daly detector. Results Under such operating conditions, an external reproducibility of <+/- 0.1 parts per thousand (2 standard deviation) for K-41/K-39 is achieved for K solutions of 1 ppm or above. Tests were carried out to evaluate the influence of total K loading, K concentration and acid molarity mismatch, matrix effects, and Ar-40(+) and (ArH+)-Ar-40-H-1 tailing on K isotope analysis. We found that the accuracy of K isotope analysis can be compromised by concentration mismatch of sample and standard K, by 0.007 parts per thousand in delta K-41 per 1% mismatch of K content. By contrast, mismatch of HNO3 molarity or existence of HCl in HNO3 exerts negligible influences on the analytical precision and accuracy of K isotope analysis. Furthermore, K isotope analytical results remain accurate when Na/K, Mg/K, Ca/K, Rb/K, V/K, and Cr/K ratios are below 3%. Conclusions The high-precision K isotope analytical method reported here is robust for studies on K isotopic variations in geological, cosmochemical, and biological samples. The f(41)K values of six international geostandards measured using our method are consistent with data measured using different analytical methods from other laboratories.
Improved ion-exchange column chromatography for Cu purification from high-Na matrices and isotopic analysis by MC-ICPMS

James Andrew Kidder,Alexandre Voinot,Kaj Vaughan Sullivan,Donald Chipley,Marissa Valentino,Daniel Layton-Matthews,Matthew Leybourne

DOI: https://doi.org/10.1039/c9ja00359b

2020-01-01

Journal of Analytical Atomic Spectrometry

Abstract:Measurements of Cu isotopes from low concentration and high salinity matrices require high recovery and purity prior to measurement. A new automated two-stage chromatographic procedure yields highly pure Cu separations, low procedure blanks and much-improved reproducibility.

spectroscopy,chemistry, analytical
A Rapid and Simple Method for Lithium Purification and Isotopic Analysis of Geological Reference Materials by MC-ICP-MS

Guanhong Zhu,Jinlong Ma,Gangjian Wei,Le Zhang

DOI: https://doi.org/10.3389/fchem.2020.557489

IF: 5.5

2020-11-23

Frontiers in Chemistry

Abstract:A simple method has been developed to purify lithium (Li) from matrix elements in geological reference materials, using a single-column packed with AGMP-50 cation exchange resin, followed by high-precision Li isotope measurements by multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS). A series of tests, such as different types of resin, loading amount of Li, loading volumes, and various eluents, were conducted to ascertain the optimal conditions for Li purification and the effects of intensity, acidity, and presence of potential matrix elements on Li isotope measurements were also evaluated. In our experiment, Al and high-field-strength elements (HFSEs), such as Ti, Zr, and Hf, were eluted by 0.2 M HCl + 0.3 M HF, and 0.73 M HCl was used to separate Li from other matrix elements, such as Na. This method is suitable for processing large amount of Li (60–270 ng) and enabling a Li recovery of close to 100%, with effective removal of matrix elements such as Na and Ca. Besides, our method achieves low matrix interferences (e.g., Na/Li << 1 and Ca/Li << 1 for rock and seawater via a single-column procedure; Ca/Li < 2 for carbonate via a two-column procedure) and also uses small volume of eluents and is rapid (~5 h), enabling a total separation to be completed in ~0.5 d. Using this method, we report Li isotopic compositions of various geological reference materials, including igneous rocks, seawater, and carbonate. The Li isotopic compositions are consistent with the data published previously for the analyzed reference materials. As such, the reported method is ideally suited for Li separation from multiple types of geological samples prior to isotopic analysis.

chemistry, multidisciplinary
High-precision K Isotopic Analysis of Cerebrospinal Fluid and Blood Serum Microsamples via Multicollector Inductively Coupled Plasma-Mass Spectrometry Equipped with 10 13 Ω Faraday Cup Amplifier Resistors

Kasper Hobin,Marta Costas Rodríguez,Elien Van Wonterghem,Roosmarijn E. Vandenbroucke,Frank Vanhaecke

DOI: https://doi.org/10.1016/j.aca.2024.342812

IF: 6.911

2024-06-03

Analytica Chimica Acta

Abstract:Background Potassium isotopic analysis is increasingly performed in both geological and biological contexts as a result of the introduction of MC-ICP-MS instrumentation equipped with either a collision/reaction cell or having the capability of working at "extra-high" mass resolution in order to deal with spectral interference caused by argon hydride (ArH + ) ions. Potassium plays an important role in the central nervous system, and its isotopic analysis could provide an enhanced insight into the corresponding processes, but K isotopic analysis of cerebrospinal fluid is challenging due to the small volume, a few microliter only, typically available. This work aimed at developing a method for determining the K isotopic signature of serum and cerebrospinal fluid at a final K concentration of 25 ng mL -1 using Faraday cup amplifiers equipped with a 10 13 Ω resistor. Results Potassium isotope ratios obtained for reference materials measured at a final K concentration of 25 ng mL -1 were in excellent agreement with the corresponding reference values and the internal and external precision for the δ 41 K value were 0.11 ‰ (2SE, N = 50) and 0.10 ‰ (2SD, N = 6), respectively. The robustness against the presence of matrix elements and concentration mismatch between sample and standard observed at higher K concentrations is preserved at low K concentration. Finally, K isotopic analysis of serum and cerebrospinal fluid (3 to 12 μL of sample) of healthy mice of both sexes was performed, revealing a trend towards an isotopically lighter signature for female serum and cerebrospinal fluid, however being significant for serum only. Significance This work provides a robust method for high-precision K isotopic analysis at a concentration of 25 ng mL -1 . By monitoring both K isotopes, 39 K and 41 K, with Faraday cups connected to amplifiers with 10 13 Ω resistors, accurate K isotope ratio results are obtained with a two-fold improvement in internal and external precision compared to those obtained with the set-up with traditional 10 11 Ω resistors. The difference in the K isotope ratio in CSF and serum between the sexes, is possibly indicating sex-based fractionation effects during cellular uptake/release or might be affected by the hormonal effects.

chemistry, analytical
High-precision Double-Spike Sn Isotope Analysis of Geological Materials by MC-ICP-MS

Jia-Xin She,Weiqiang Li,Shichao An,Yuanfeng Cai

DOI: https://doi.org/10.1039/d2ja00339b

2022-01-01

Journal of Analytical Atomic Spectrometry

Abstract:This study proposes a new robust protocol for stable Sn isotope measurements using the double-spike method in geological reference materials with a range of sample matrices.
Development of an Automatic Column Chromatography Separation Device for Metal Isotope Analysis Based on Droplet Counting

Fei-Yang Zhou,Dong He,Xin Miao,Chun Yang,Jun-Hang Dong,Hong-Tao Zheng,Zhuo Cheng,Xing Liu,Zhen-Li Zhu

DOI: https://doi.org/10.1021/acs.analchem.1c00145

IF: 7.4

2021-05-10

Analytical Chemistry

Abstract:A novel, simple, cost-effective, reliable, and practical automatic column chromatography separation device capable of simultaneously purifying samples for radiogenic and non-traditional stable isotope analysis has been developed. The device avoids the use of any pump and features eluent driving by the siphon effect (gravity) and quantitative control by infrared droplet counting. Several factors affecting the control of droplets were investigated, including types and concentrations of eluents and the height of the liquid level. Results showed that accurate dripping of the eluent could be readily achieved by controlling the number of droplets under selected conditions. The separation performance of the device was first demonstrated by the elution of Sr and Cd in synthetic matrix solutions. The recoveries of Sr and Cd samples were better than 87.6 and 95.0%, respectively, and the whole procedure blank was about 0.3 ng for Sr and 0.1 ng for Cd. Finally, the reliability of the device was further validated by the purification of Sr and Cd from different geological reference materials (NIST 2711a, Nod-A-1, BCR-2, and BHVO-2). The determined Cd and Sr isotope values agree well with their reference values within the uncertainty range. All these results clearly demonstrate the reliability and practicability of the proposed device, which provides a promising method for the automated purification of isotope samples.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.analchem.1c00145?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.analchem.1c00145</a>.Sample preparation and digestion procedures for standard geological samples, instrumental operating conditions of the Nu Plasma II MC-ICP-MS, method description for isotope separation by SID, stability of quantitative control for ultrapure water in different volumes by SID, diagrams of the detailed electrical systems of the components, and logical control diagrams of the separation programs (<a class="ext-link" href="/doi/suppl/10.1021/acs.analchem.1c00145/suppl_file/ac1c00145_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

chemistry, analytical
High-Precision Measurements of 44 Ca/ 40 Ca Using Multiple-Collector Inductively Coupled Plasma Mass Spectrometry without Collision-Cell Technology

Hai-Ou Gu,Xiya Liu,He Sun,Guochao Sun,Dongyong Li,Fangyue Wang,Can Ge,Yu Fan,Taofa Zhou

DOI: https://doi.org/10.1021/acs.analchem.3c04823

IF: 7.4

2024-04-11

Analytical Chemistry

Abstract:Herein, we present a new method for determining the Ca isotopic composition of geological samples. To eliminate matrix elements from Ca, a column chromatography method was developed using a N,N,N'N' tetraoctyl-1,5-diglycolamide (TODGA) resin. The Ca isotopic compositions were measured by a multiple collector inductively coupled plasma mass spectrometry (MC-ICP-MS) without collision cell equipment, especially that direct measurement to ^(44)Ca/^(40)Ca can be achieved. To mitigate the interference...

chemistry, analytical
Efficient purification for Li and high-precision and accuracy determination of Li isotopic compositions by MC-ICP-MS

GOU Long-fei,JIN Zhang-dong,DENG Li,SUN He,YU Hui-min,ZHANG Fei

DOI: https://doi.org/10.3969/j.issn.0379-1726.2017.06.003

2017-01-01

Abstract:Efficient isolation and purification of lithium (Li) were accomplished for various environmental and geological samples by a series of iterative experiments.These experiments led to the creation of a set of recommended experimental conditions including an 8 mL column volume,AG 50W-X12 resin,and 0.5 mol/L HNO3 eluent.Eluate was collected during a single leach in the volume interval between 20 and 48 mL to achieve a complete purification and recovery of Li.Nevertheless,for samples in a hyperhaline matrix,a double purification procedure is suggested to ensure that Na/Li ＜ 1,which is essential for measuring the isotopic composition of Li on a multi-collector inductively coupled plasma mass spectrometer (MC-ICP-MS).In this work,isotopic composition was determined using a Neptune Plus MC-ICP-MS.The δ7Li of a laboratory-mixed solution (IEECAS-Li) purified by our procedure was measured to be 8.31‰ ± 0.12‰,which is in agreement with that of the corresponding single element standard before mixing,8.33‰ ± 0.20‰.Following our purification procedure,the δ7Li values of USGS international rock reference materials (AGV-2 and BHVO-2) and seawater reference material NASS-6 were measured as 6.83‰ ± 0.75‰,4.32‰ ± 0.33‰,and 31.10‰ ± 0.60‰ (2 s.d.,n =5),respectively,all of which are within the range of error of the reported values.As a result,we propose a one-step purification procedure for Li and then an accurate and high-precision determination of its isotopic compositions by MC-ICP-MS.The purification protocol was then used to separate Li from samples of river water,lake water,and loess.The multiply measured δ7Li values of six such samples with Li concentrations ranging from 15 ng/g to 90 μg/g had two-time standard derivations better than 0.30‰ with excellent reproducibility,demonstrating the high-level precision and the accuracy possible for Li isotopic measurements.This purification protocol is especially suitable for environmental samples with very low Li contents.

An optimal separation method for high-precision K isotope analysis by using MC-ICP-MS with a dummy bucket

High-precision Analysis of Potassium Isotopes by MC-ICP-MS Without Collision Cell Using Cool Plasma Technique in Low-Resolution Mode

High-precision Determination of Stable Potassium and Magnesium Isotopes Utilizing Single Column Separation and Multicollector Inductively Coupled Plasma Mass Spectrometry

High precision potassium isotope analysis of geological samples using MC-ICP-MS

Precise measurement of stable potassium isotope ratios using a single focusing collision cell multi-collector ICP-MS

Optimization of analytical conditions for precise and accurate isotope analyses of Li, Mg, Fe, Cu, and Zn by MC-ICPMS

An Efficient Li Dual-Column System and High-Precision Li Isotope Measurement of High Matrix and Low-Li Samples by MC-ICP-MS

Low-Consumption and High-Efficiency Isotope Analysis by Microultrasonic Single-Droplet Nebulization Sampling Multicollector Inductively Coupled Plasma Mass Spectrometry

Isotope Separation of Potassium with a magneto-optical combined method

High precision analysis of potassium stable isotopes using the collision/reaction cell Neoma MC-ICPMS/MS

Precise magnesium isotope analyses of high-K and low-Mg rocks by MC-ICP-MS

A single-column and efficient procedure for separating Fe and Mg from geological materials for isotopic analyses using MC-ICP-MS

Author Response for "application of a “continuous‐acquisition‐method” to Potassium Isotope Measurement by Multi‐collector Inductively Coupled Plasma Mass Spectrometry"

Precise Measurement of 41 K/ 39 K Ratios by High-Resolution Multicollector Inductively Coupled Plasma Mass Spectrometry under a Dry and Hot Plasma Setting

Improved ion-exchange column chromatography for Cu purification from high-Na matrices and isotopic analysis by MC-ICPMS

A Rapid and Simple Method for Lithium Purification and Isotopic Analysis of Geological Reference Materials by MC-ICP-MS

High-precision K Isotopic Analysis of Cerebrospinal Fluid and Blood Serum Microsamples via Multicollector Inductively Coupled Plasma-Mass Spectrometry Equipped with 10 13 Ω Faraday Cup Amplifier Resistors

High-precision Double-Spike Sn Isotope Analysis of Geological Materials by MC-ICP-MS

Development of an Automatic Column Chromatography Separation Device for Metal Isotope Analysis Based on Droplet Counting

High-Precision Measurements of 44 Ca/ 40 Ca Using Multiple-Collector Inductively Coupled Plasma Mass Spectrometry without Collision-Cell Technology

Efficient purification for Li and high-precision and accuracy determination of Li isotopic compositions by MC-ICP-MS