Abstract:It is essential to study the tensile fracture mechanism of additively manufactured materials and develop the effective process treatment techniques to improve their fracture resistance. In this paper, the effects of different treatment processes on the microstructure and tensile fracture properties of TC17 titanium alloy melted by laser selective zone melting were investigated. The static tensile fracture morphological characteristics were observed by combining SEM and EDS. The metallographic microstructure after chemical corrosion was observed optically. And the tensile fracture morphology of the three states of TC17 titanium alloy samples at room temperature conditions was investigated. The results show that the metallographic matrix microstructure of TC17 titanium alloy after HT, HIP and HIP-HT treatments was a bimodal structure with α+β phases, i.e., β phase was in the form of a net basket, and α phase was in the form of a coarse bar. The grain sizes of the samples treated by different processes were different, but the difference in grain size of the HT-treated tissues was small, and the difference in grain size of the HIP-HT-treated tissues was large. And the coarse α-phase segregation could be seen at the edge of the samples. The 3D-printed materials had complex changes in anisotropic properties affected by the printing structure and tissue. The printed tissues were brittle and had high internal stresses. These problems were partly improved at high temperatures, but they still existed. The HIP-HT-treated materials had a large α+β-phase bimodal structure. The HT-treated material had coarse grains and precipitation phases, poor room temperature plasticity, and improved high temperature plasticity. After HT treatment, the original printing microstructure changed, the strength and plasticity were significantly improved, but the macroscopic printing structure still had a slight influence on the fracture morphology. When HIP treatment temperature was higher, the influence of macroscopic printing structure basically disappeared, but the grain and microstructure grew up, and the strength and plasticity were slightly lower than that of the HT treatment. HIP process basically eliminated the unfused defects of the three-dimensional morphology, and the local weak bonding zone formed.

Microstructural Characteristics and Mechanical Properties of Repaired Titanium Alloy Blade by Arc Additive Manufacturing Process

Titanium Alloy Repair with Wire-Feed Electron Beam Additive Manufacturing Technology

In-situ investigation on tensile deformation and fracture behaviors of inhomogeneous microstructure during laser repair of Ti-6Al-4 V titanium alloy

Directed energy deposition‐arc repair Al6.5Cu2Ni0.3Ti0.5Zr0.25V alloy: Microstructure evolution and Strengthening mechanism

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Microstructures and mechanical properties of Ti6Al4V alloy repaired by the technology of point-mode forging and laser repairing

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Effect of Heat Treatment on Microstructure and Mechanical Properties of Titanium Alloy Fabricated by Laser–Arc Hybrid Additive Manufacturing

A novel magnetic field assisted powder arc additive manufacturing for Ti60 titanium alloy: Method, microstructure and mechanical properties

Effects of different treatment processes on microstructure and tensile fracture behaviour of selected laser melting TC17 titanium alloy

Microstructure and Mechanical Properties of 600℃High Temperature Titanium Alloy Fabricated by Additive Manufacturing

Tailoring Weldability for Microstructures in Laser-Welded Near-α Titanium Alloy: Insights on Mechanical Properties

Microstructural evolution and mechanical property of Ti-6Al-4V wall deposited by continuous plasma arc additive manufacturing without post heat treatment

Microstructure and mechanical properties of laser additive manufactured novel titanium alloy after heat treatment

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties

A Review of Additive Manufacturing Techniques and Post-Processing for High-Temperature Titanium Alloys

The Martensitic Transformation and Mechanical Properties of Ti6Al4V Prepared Via Selective Laser Melting

Mechanical Behavior of Additive Manufacturing (AM) and Wrought Ti6Al4V with a Martensitic Microstructure

Effect of substrate temperature on microstructure and mechanical properties of TiAl alloy fabricated using the twin-wire plasma arc additive manufacturing system

Effects of V Element and Heat Treatment Process on Microstructure and Mechanical Properties of Additive Manufacturing of Titanium Aluminum Alloy Using Flux-Core Arc Welding Wire with TiH2 Powder