Abstract:BackgroundControlled low strength materials (CLSM), known as flow able fill is used as a replacement of compacted soil in cases where the application of the latter is difficult or impossible. The low mechanical requirements compared with concrete enable the use of industrial wastes for the production of CLSM. In general, CLSM mixtures consist of standard materials such as Portland cement, fly ash, fine aggregate and water. However, other industrial by-products and recycled materials are also accepted and encouraged as long as they are considered to be available, cost-effective for specific application and the necessary characteristics of the mixture such as flowability, strength, excavatability, and density are acceptable.MethodsThe aim of this study is to evaluate the feasibility of incorporating red mud as a partial replacement for Portland cement into a controlled low-strength material (CLSM) made by industrial by-products (e.g., ponded ash and fly ash). A control mixture was initially produced with ponded ash, Portland cement, Class F fly ash, and water. For other mix proportions, red mud was substituted for Portland cement in amounts of 5, 10, 15, 20, 25, and 30 % by weight. The bleeding, flowability, fresh density, initial setting time of fresh CLSM mixtures were measured and the follows were hardened ones including compressive strength, corrosivity.ResultsExpectedly, all general properties of CLSM incorporating red mud did fall within the acceptable ranges. They performed well and conformed to the requirements of CLSM in ACI 229 standards with regard to flowability, bleeding rate, initial setting time, corrosivity and unconfined compressive strength.ConclusionsThe partial replacement of cement by red mud, possibly up to 30 % in mixtures, would reduce flowability and slightly increase corrosivity evidenced by pH but still meet the requirements. Especially, it was found that an increase in red mud content could lead to an improvement in the stability (bleeding rate) and accelerate the setting process on the performances of the proposed CLSM. Finally, with regard to strength at 28 days, CLSM with highest strength could be produced by an optimum replacement of 15 % red mud to cement. In overall, it is worth noting that red mud could be feasible and potential in use as a partial replacement to Portland cement in CLSM production.

Red Mud as a Controlled Low Strength Material

Engineering properties of controlled low strength material (CLSM) incorporating red mud

Effects of Red Mud on Workability and Mechanical Properties of Autoclaved Aerated Concrete (AAC)

Preparation of controlled low-strength materials from alkali-excited red mud-slag-iron tailings sand and a study of the reaction mechanism

Optimization of Controlled Low-Strength Material from Multi-Component Coal-Based Solid Waste

Material properties and environmental implications of red mud solidified with blast-furnace slag, silica fume, and sodium hydroxide

Evaluation of blends bauxite-calcination-method red mud with other industrial wastes as a cementitious material: properties and hydration characteristics.

Experimental Investigation on Red Mud from the Bayer Process for Cemented Paste Backfill

Mine Tailings and Bottom Ash from Waste Incineration as Alternative Fine Aggregates for Controlled Low-Strength Materials

Development and Characterization of Sustainable Cement-Free Controlled Low Strength Material Using Titanium Gypsum and Construction Waste Soil

Influence of Red Mud on the Engineering and Microstructural Properties of Sustainable Ultra-High Performance Concrete

Utilization of Red Mud with High Radiation for Preparation of Autoclaved Aerated Concrete (AAC): Performances and Microstructural Analysis

Utilization of waste marine dredged clay in preparing controlled low strength materials with polycarboxylate superplasticizer and ground granulated blast furnace slag

Upcycling of wastes for sustainable controlled low-strength material: A review on strength and excavatability

Characterization of controlled low-strength material obtained from dewatered sludge and refuse incineration bottom ash: mechanical and microstructural perspectives

Properties of Red Mud Blended Magnesium Phosphate Cements: Workability and Microstructure Evolution

The synergistic hydration mechanism and environmental safety of multiple solid wastes in red mud-based cementitious materials

Preparing controlled low strength materials (CLSM) using excavated waste soils with polycarboxylate superplasticizer

Sustainable controlled low strength material from waste materials for infrastructure applications: State-of-the-art

Development of insulating backfill materials produced from the ternary mixtures of red mud, fly ash and preformed foam

Effect of Red Mud on Mechanical Properties of Loess–Containing Aluminosilicate Based Cementitious Materials