Abstract:BackgroundControlled low strength materials (CLSM), known as flow able fill is used as a replacement of compacted soil in cases where the application of the latter is difficult or impossible. The low mechanical requirements compared with concrete enable the use of industrial wastes for the production of CLSM. In general, CLSM mixtures consist of standard materials such as Portland cement, fly ash, fine aggregate and water. However, other industrial by-products and recycled materials are also accepted and encouraged as long as they are considered to be available, cost-effective for specific application and the necessary characteristics of the mixture such as flowability, strength, excavatability, and density are acceptable.MethodsThe aim of this study is to evaluate the feasibility of incorporating red mud as a partial replacement for Portland cement into a controlled low-strength material (CLSM) made by industrial by-products (e.g., ponded ash and fly ash). A control mixture was initially produced with ponded ash, Portland cement, Class F fly ash, and water. For other mix proportions, red mud was substituted for Portland cement in amounts of 5, 10, 15, 20, 25, and 30 % by weight. The bleeding, flowability, fresh density, initial setting time of fresh CLSM mixtures were measured and the follows were hardened ones including compressive strength, corrosivity.ResultsExpectedly, all general properties of CLSM incorporating red mud did fall within the acceptable ranges. They performed well and conformed to the requirements of CLSM in ACI 229 standards with regard to flowability, bleeding rate, initial setting time, corrosivity and unconfined compressive strength.ConclusionsThe partial replacement of cement by red mud, possibly up to 30 % in mixtures, would reduce flowability and slightly increase corrosivity evidenced by pH but still meet the requirements. Especially, it was found that an increase in red mud content could lead to an improvement in the stability (bleeding rate) and accelerate the setting process on the performances of the proposed CLSM. Finally, with regard to strength at 28 days, CLSM with highest strength could be produced by an optimum replacement of 15 % red mud to cement. In overall, it is worth noting that red mud could be feasible and potential in use as a partial replacement to Portland cement in CLSM production.

Upcycling of wastes for sustainable controlled low-strength material: A review on strength and excavatability

Application of Controlled Low Strength Material in Backfilling of Pipe Trench

Development of Sustainable Self-Compacting Concrete Using Recycled Concrete Aggregate and Fly Ash, Slag, Silica Fume

Mechanical and Durability Properties of Sustainable Self-Compacting Concrete with Recycled Concrete Aggregate and Fly Ash, Slag and Silica Fume

Sustainable utilization of industrial wastes in controlled low-strength materials: a review

Sustainable controlled low strength material from waste materials for infrastructure applications: State-of-the-art

Preparing controlled low strength materials (CLSM) using excavated waste soils with polycarboxylate superplasticizer

Optimization of Controlled Low-Strength Material from Multi-Component Coal-Based Solid Waste

Mine Tailings and Bottom Ash from Waste Incineration as Alternative Fine Aggregates for Controlled Low-Strength Materials

Research Progress on Controlled Low-Strength Materials: Metallurgical Waste Slag as Cementitious Materials

Characterization of controlled low-strength material obtained from dewatered sludge and refuse incineration bottom ash: mechanical and microstructural perspectives

Engineering properties of controlled low strength material (CLSM) incorporating red mud

Harnessing hazardous wastes: the production, characterization, and performance of controlled low strength materials using common effluent treatment plant sludge

Utilization of waste marine dredged clay in preparing controlled low strength materials with polycarboxylate superplasticizer and ground granulated blast furnace slag

Development and Characterization of Sustainable Cement-Free Controlled Low Strength Material Using Titanium Gypsum and Construction Waste Soil

Application of the Taguchi Method for Optimizing the Process Parameters of Producing Controlled Low-Strength Materials by Using Dimension Stone Sludge and Lightweight Aggregates

Evaluating the strength characteristics of mixtures of municipal solid waste incineration bottom ash and reddish laterite clay for sustainable construction

An Evaluative Review of Recycled Waste Material Utilization in High-Performance Concrete

Experimental Study and Application of Controlled Low-Strength Materials in Trench Backfilling in Suqian City, China

Applying Circular Economy to Construction Industry through Use of Waste Materials: A Review of Supplementary Cementitious Materials, Plastics, and Ceramics