Abstract:With the rapid growth of shield-discharged soil (SDS), there is an increasing demand for effective recycling and transformation methods. This study aims to develop an alkali-activated controlled low-strength material (CLSM) by utilizing ground granulated blast furnace slag (GGBFS) and fly ash (FA) as precursors, SDS as fine aggregate, and sodium hydroxide (NaOH) solution as an activator. The Box-Behnken design (BBD) within the response surface methodology (RSM) framework was employed, considering liquid-to-solid ratio, alkali equivalent, aggregate-to-binder ratio, and foam agent content (FC) in SDS as key factors. Regression models were constructed to analyze the effects of these factors on flowability, bleeding rate, setting time, compressive strength, elastic modulus, and water absorption. The results confirmed the effectiveness of RSM in determining optimal conditions for material performance. In addition, microscopic analyses were conducted to explore hydration products, microstructural characteristics, and pore distribution. The findings revealed that the fresh density of the CLSM ranged from 1460 to 1740 kg/m3, classifying it as a low-density material. The 28-day compressive strength varied from 1.837 to 7.884 MPa, while the setting time ranged between 1.2 and 5.6 hours. These properties comply with the ACI 229 standard and are suitable for practical applications. Interestingly, when the aggregate-to-binder (A/B) ratio was between 0.2 and 0.4, increasing the ratio did not lead to a consistent reduction in mechanical properties. Instead, the properties initially decreased and then improved. Moreover, an increase in foam agent content (FC) extended the setting time and reduced mechanical strength. The correlation coefficients of all models exceeded 0.98, with a coefficient of variation below 10 % and a signal-to-noise ratio greater than 4, demonstrating strong reliability and accuracy of the models. Additionally, the average relative error between predicted and experimental values in six scenarios was under 6 %, validating the feasibility of optimizing the design of alkali-activated CLSM using RSM. The formation of Ca(OH)2 crystals facilitates early strength development, resulting in final cementitious materials reticular, fibrous C-S-H, C-A-H, and other gel-like hydration products. Calcium promotes the formation of gels such as C-S-H, shortening the setting time and enhancing microstructural density. This study provides valuable insights for optimizing the design of alkali-activated CLSM containing SDS, thereby expanding methods for utilizing construction and demolition waste.

Development of insulating backfill materials produced from the ternary mixtures of red mud, fly ash and preformed foam

Development of Sustainable Self-Compacting Concrete Using Recycled Concrete Aggregate and Fly Ash, Slag, Silica Fume

Effects of Red Mud on Workability and Mechanical Properties of Autoclaved Aerated Concrete (AAC)

Engineering properties of controlled low strength material (CLSM) incorporating red mud

Foamed concrete utilizing excavated soil and fly ash for urban underground space backfilling: Physical properties, mechanical properties, and microstructure

Utilization of Red Mud with High Radiation for Preparation of Autoclaved Aerated Concrete (AAC): Performances and Microstructural Analysis

Effect of Cementitious Material Composition on the Performance of Low-Carbon Foamed Lightweight Soil

Experimental Study and Application of Controlled Low-Strength Materials in Trench Backfilling in Suqian City, China

A Feasibility Study of Low Cement Content Foamed Concrete Using High Volume of Waste Lime Mud and Fly Ash for Road Embankment

Multisolid waste collaborative production of aeolian sand-red mud-fly ash cemented paste backfill

Preparation of controlled low-strength materials from alkali-excited red mud-slag-iron tailings sand and a study of the reaction mechanism

Investigation of hierarchical porous cold bonded lightweight aggregates produced from red mud and solid-waste-based cementitious material

Optimization and characterization of GGBFS-FA based alkali-activated CLSM containing Shield-discharged soil using Box-Behnken response surface design method

Development of an environmentally foamed concrete incorporating red mud

Optimization of Controlled Low-Strength Material from Multi-Component Coal-Based Solid Waste

Microstructure Analysis and Mechanical Properties of Backfill Material Using Stone Sludge

Experimental study on the stabilization of marine soft clay as subgrade filler using binary blending of calcium carbide residue and fly ash

Performance evaluation of modified marine dredged soil and recycled in-situ soil as controlled low strength materials for underground pipe

Preparation and Performance Study of Large Volume Foamed Lightweight Soil for an Intelligent Networked Vehicle Test Site

Production of a new type of cemented paste backfill with solid waste from carbide slag, soda residue, and red mud: mechanism, optimization, and its environmental effects

Optimization of Proportions and Solidification Mechanism of All-Solid Waste Cementitious Materials Based on Circulating Fluidized Bed Fly Ash, Calcium Carbide Slag, and Red Mud