Abstract:With the rapid growth of shield-discharged soil (SDS), there is an increasing demand for effective recycling and transformation methods. This study aims to develop an alkali-activated controlled low-strength material (CLSM) by utilizing ground granulated blast furnace slag (GGBFS) and fly ash (FA) as precursors, SDS as fine aggregate, and sodium hydroxide (NaOH) solution as an activator. The Box-Behnken design (BBD) within the response surface methodology (RSM) framework was employed, considering liquid-to-solid ratio, alkali equivalent, aggregate-to-binder ratio, and foam agent content (FC) in SDS as key factors. Regression models were constructed to analyze the effects of these factors on flowability, bleeding rate, setting time, compressive strength, elastic modulus, and water absorption. The results confirmed the effectiveness of RSM in determining optimal conditions for material performance. In addition, microscopic analyses were conducted to explore hydration products, microstructural characteristics, and pore distribution. The findings revealed that the fresh density of the CLSM ranged from 1460 to 1740 kg/m3, classifying it as a low-density material. The 28-day compressive strength varied from 1.837 to 7.884 MPa, while the setting time ranged between 1.2 and 5.6 hours. These properties comply with the ACI 229 standard and are suitable for practical applications. Interestingly, when the aggregate-to-binder (A/B) ratio was between 0.2 and 0.4, increasing the ratio did not lead to a consistent reduction in mechanical properties. Instead, the properties initially decreased and then improved. Moreover, an increase in foam agent content (FC) extended the setting time and reduced mechanical strength. The correlation coefficients of all models exceeded 0.98, with a coefficient of variation below 10 % and a signal-to-noise ratio greater than 4, demonstrating strong reliability and accuracy of the models. Additionally, the average relative error between predicted and experimental values in six scenarios was under 6 %, validating the feasibility of optimizing the design of alkali-activated CLSM using RSM. The formation of Ca(OH)2 crystals facilitates early strength development, resulting in final cementitious materials reticular, fibrous C-S-H, C-A-H, and other gel-like hydration products. Calcium promotes the formation of gels such as C-S-H, shortening the setting time and enhancing microstructural density. This study provides valuable insights for optimizing the design of alkali-activated CLSM containing SDS, thereby expanding methods for utilizing construction and demolition waste.

Investigation of hierarchical porous cold bonded lightweight aggregates produced from red mud and solid-waste-based cementitious material

Study on preparation and activation enhancement effect of cold bonded multi-solid waste wrap-shell lightweight aggregates (SWSLAs) with low cement content

Preparation and Properties of Alkali-Activated Red Mud-Based Artificial Lightweight Aggregates

Efficient Utilization of Waste Marine Clay for Fine Aggregate to Develop Sustainable and Cost-Effective Strain-Hardening Cement-Based Composites

Novel recycling application of high volume municipal solid waste incineration bottom ash (MSWIBA) into sustainable concrete

Innovative synthesis of low-carbon cemented backfill materials through synergistic activation of solid wastes: An integrated assessment of economic and environmental impacts

Developing Low-Carbon High-Strength Core-Shell Aggregates Using Solid Waste by Cold-Bonding Techniques

Utilization of waste marine dredged clay in preparing controlled low strength materials with polycarboxylate superplasticizer and ground granulated blast furnace slag

Valorization of municipal solid waste incineration bottom ash (MSWIBA) into cold-bonded aggregates (CBAs): Feasibility and influence of curing methods

Development of Cement-Free Bio-Based Cold-Bonded Lightweight Aggregates (bcblwas) Using Steel Slag and Miscanthus Powder Via CO2 Curing

Optimization of Proportions and Solidification Mechanism of All-Solid Waste Cementitious Materials Based on Circulating Fluidized Bed Fly Ash, Calcium Carbide Slag, and Red Mud

Optimization of Controlled Low-Strength Material from Multi-Component Coal-Based Solid Waste

Manufacturing and performance of environment-friendly lightweight aggregates with core-shell structure

Synergistic Activation Mechanism and Long-Term Properties of a Solid Waste Cementitious Materials Based on Red Mud and Calcium Carbide Slag

The synergistic hydration mechanism and environmental safety of multiple solid wastes in red mud-based cementitious materials

A low-carbon approach to recycling engineering muck to produce non-sintering lightweight aggregates: Physical properties, microstructure, reaction mechanism, and life cycle assessment

Investigation on the fabrication of lightweight aggregate with acid-leaching tailings of vanadium-bearing stone coal minerals and red mud

Optimization and characterization of GGBFS-FA based alkali-activated CLSM containing Shield-discharged soil using Box-Behnken response surface design method

Preparation and Research on Mechanical Properties of Eco-Friendly Geopolymer Grouting Cementitious Materials Based on Industrial Solid Wastes

Production of a new type of cemented paste backfill with solid waste from carbide slag, soda residue, and red mud: mechanism, optimization, and its environmental effects

Design and Preparation Technology of Green Multiple Solid Waste Cementitious Materials