Abstract:Organic-inorganic hybrid perovskites have attracted substantial attention due to their outstanding performance in solar energy conversion and optoelectronic applications. However, the poor stability of organic lead halide perovskites (APbX(3), A: organic cations; X: halide anions) hinders their practical application. Compositional engineering, optimizing the concentration of different A and/or X, is one of the most effective ways to enhance the stability of APbX(3). In particular, mixing formamidinium (FA) and methylammonium (MA) cations has been widely investigated. Here, we performed first-principles calculations to systematically investigate the structures and optical properties of FA(1-x)MA(x)PbI(3). We obtained several stable crystal structures of FA(1-x)MA(x)PbI(3) in the cubic phase for different ratios of FA and MA cations. By analyzing the structures of these mixed cation perovskites, we revealed that the lattice parameters decreased linearly with increasing concentration of MA cations, which was consistent with previous experimental results. For APbX(3) perovskites, the Goldschmidt tolerance factor has been shown to be an effective index for predicting the stability. The mixing of organic cations is an effective method for adjusting this factor and thus the stability of these perovskite materials. In this work, the formation energy difference (Delta E) was calculated and our results showed that mixing of FA and MA cations could increase the thermodynamic stability compared to pure FAPbI(3) and MAPbI(3). FA(0.5)MA(0.5)PbI(3) was found to be the most stable of all composites investigated. Furthermore, the band gap decreased with increasing proportion of FA cations, indicating an effective strategy for extending the absorption range of organic-inorganic hybrid perovskites into the infra-red region of the solar spectrum. By analyzing the Pb-I bond lengths for different FA : MA ratios, we showed that the decrease of band gap mainly comes from the increase of the maximum valence band energy. In addition, the effective masses were similar, irrespective of the cation mixture, indicating that the mixing of organic cations does not affect the carrier transport mechanism in this material. Density of states (DOS) analysis revealed that the DOS of valence band edge increased with increasing proportion of FA cations, enhancing transitions between the valence and conduction bands. Finally, detailed analysis of the optical absorption coefficients of all composition was performed; the absorption spectra were blue shifted with increasing MA cation concentration. These results demonstrated the possibility of controlling the optoelectronic properties of organometallic lead halide perovskites by mixing FA and MA cations and hence, further improving the efficiency of perovskite solar cells.

Synthesis and optimization of properties of thin films of FAx(MA1-X)PbI3grown by spin coating with perovskite structure to be used as active layer in hybrid solar cells

Reproducible One-Step Fabrication of Compact MAPbl(3-x)Cl(x) Thin Films Derived from Mixed-Lead-Halide Precursors

The Intrinsic Properties of FA(1−x)MAxPbI3 Perovskite Single Crystals

Mixed-Organic-Cation (FA)x(MA)1-xPbI3 Planar Perovskite Solar Cells with 16.48% Efficiency via a Low-Pressure Vapor-Assisted Solution Process

First-Principles Study of Mixed Cation Methylammonium-Formamidinium Hybrid Perovskite

Effects of Spin-Coating Speed and Precursor Concentration in Formamidinium-based Layered Perovskite Films

Sequential Introduction of Cations Deriving Large-Grain Cs(X)Fa(1-X)Pbi(3) Thin Film for Planar Hybrid Solar Cells: Insight into Phase-Segregation and Thermal-Healing Behavior

Ultrafast Growth of High-Quality Cs 0.14 FA 0.86 Pb(Br x I 1– x ) 3 Thin Films Achieved Using Super-Close-Space Sublimation

CsI Pre-Intercalation in the Inorganic Framework for Efficient and Stable FA 1- x Cs x PbI 3 (Cl) Perovskite Solar Cells.

Modulation of Nucleation and Crystallization in PbI2 Films Promoting Preferential Perovskite Orientation Growth for Efficient Solar Cells

Constructing Graded Perovskite Homojunctions by Adding Large Radius Phenylmethylamine Ions for Sequential Spin-Coating Deposition Method To Improve the Efficiency of Perovskite Solar Cells

Regulating the crystalline phase of intermediate films enables FA 1− x MA x PbI 3 perovskite solar cells with efficiency over 22%

Stable α‐FAPbI3 via porous PbI2 for efficient perovskite solar cells

Optoelectronic property refinement of FASnI3 films for photovoltaic application

Effect of Processing Technique Factors on Structure and Photophysical Properties of Perovskite Absorption Layer by Using Two-Step Spin-Coating Method

Study of hybrid organic–inorganic halide perovskite solar cells based on MAI[(PbI2)1−x(CuI)x] absorber layers and their long-term stability

Fabrication and Characterization of FA x Cs 1− x PbI 3 Polycrystal Perovskite Solar Cells

High-quality All-Inorganic CsPbI2Br Thin Films Derived from Phase-Pure Intermediate for Efficient Wide-Bandgap Perovskite Solar Cells

Mixed Cation FAxPEA1–xPbI3 with Enhanced Phase and Ambient Stability toward High‐Performance Perovskite Solar Cells

Enhanced stability in CH3NH3PbI3 hybrid perovskite from mechano-chemical synthesis: structural, microstructural and optoelectronic characterization

Multifunctional anion-cation modulation engineering for Sn-Pb perovskite solar cells